User manual SMEG WD-CONNECT

[. . . ] 5 APPLICATION INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4. 1 4. 2 4. 3 4. 4 OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] It cannot be used with different devices. Once the connection is established, the user can: - Download the internal memory archive (Cycles Log) to keep track of disinfection cycles performed. - Set the parameters for LAN network communication. Moreover the technician can: - Download an updated version of the machine firmware. The application is intended for personnel responsible for the equipment ("Responsible Body ") identified with the title of "Superuser". The basic user is not authorized to use the application. ESSENTIAL REQUIREMENTS    Operating system: Microsoft Windows 32 or 64bit, Windows 7 or more recent version, with Microsoft . NET Framework updated version. “USB” port functioning properly with updated drivers (especially the reference driver "STM32 virtual com port"). Cable “USB male - USB male”, 2 meters length (or lower) for the connection between PC and machine. 2 COMPATIBILITY – DEVICES The SOFTWARE can be used together with the following devices: GW SERIES – LABORATORY GLASSWARE WASHERS GW6010 WD SERIES – MEDICAL WASHER DISINFECTORS WD6010 4 3 INSTALLATION DRIVER “STM32 Virtual com port” installation Step 1: driver installation “STM32 virtual com port” (the driver can be found in the folder: “STM32 virtual com port” – it is also possible to download the driver file from the original website www. st. com). Uninstall previous versions, if any (E. g. A green circle next to the button will indicate whether the connection is successfully established. The circle is red if you can not connect. Please note: If the connection fails, there may be an error in the selection - retry checking the port actually used. 7 LAN PARAMETERS – IP CONFIGURATION Only if installed the optional to connect the device to the LAN, using this screen the Superuser can set the parameters for the communication. CAUTION: The following are network settings, they need to be set by competent staff with the help of the of the computer system administrator. 3 active icons: - Read: to read the current values set in the CPU motherboard. - Write Flash: to write, on the CPU of the device, the values entered in this form. - FAB recovery: to restore as current, factory-set values. 8 CYCLES LOG – ARCHIVE MENAGEMENT DOWNLOAD CYCLES LOG FILE With this screen, the user can download on the PC a "txt" Archive-file: the cycles recordings contained in the memory of the machine. Select the destination path of the file; 2. [. . . ] Warning: the clear memory operation is irreversible, the deleted data can not be recovered in any way. You cannot delete the file from the device memory until you've successfully completed the export process on the PC. Make sure you install the required version of Microsoft . NET Framework. [. . . ]