User manual SMEG WD5090

[. . . ] WARNING: If the appliance is equipped with a glass cover, the latter may shatter if heated. Turn off all the burners and wait a few minutes before closing the cover. The product label, with the serial number, is sticked under the hob. The manufacturer refuses all responsibility for possible damages to things or people, resulting from a wrong installation or from an improper, incorrect or unreasonable use of this equipment 10 DESCRIPTION MOD. WD5090 2 Semi-rapid burner 1650 W 4 Wok burner 7 Battery housing 8 Control knob for burner 4000 W 11 INSTRUCTIONS FOR THE USER IT IS NECESSARY THAT ALL THE OPERATIONS REGARDING THE INSTALLATION, ADJUSTMENT AND ADAPTATION TO THE TYPE OF GAS AVAILABLE ARE CARRIED OUT BY QUALIFIED PERSONNEL, IN CONFORMITY WITH THE REGULATIONS IN FORCE. [. . . ] Use the maximum capacity to quickly make the liquids reach the boiling temperature, and the reduced capacity to heat food or maintain boiling. All of the operating positions must be chosen between the maximum and the minimum ones, never between the minimum position and the closing point. The gas supply can be interrupted by turning the knob clockwise up to the closing position. closing position If there is no power supply, it is possible to light the burners with matches, setting the knob to the startup point (large flame). BURNERS Semi-rapid Wok Power W 1650 4000 Ø of pots 16 - 18 cm 24 - 26 cm Notice - When the equipment is not working, always check that the knobs are in the closing position (see fig. 1). - With the models with the safety valve, if the flame should blow out accidentally, the safety valve will automatically stop the gas supply, after a few seconds. To restore operation, set the knob to the lighting point (large flame, fig. 1). - While cooking with fat or oil, pay the utmost attention as these substances can catch fire when overheated. - Do not use sprays near the appliance in operation. - Do not place unstable or deformed pots on the burner, so as to prevent them from overturning or overflowing. - Make sure that pot handles are placed properly. - When the burner is started up, check that the flame is regular and, before taking pots away, always lower the flame or put it out. maximum position minimum position 1 12 2 INSTRUCTIONS FOR THE USER CLEANING Don't use a steam cleaner for the cleaning the hob. Therefore, it is necessary to discharge these smokes outside. The room where this appliance is installed must have a natural air inflow, so as to ensure a regular gas combustion and room ventilation: the necessary air volume must not be lower than 20m3. Air must come from permanent openings made on the room walls that communicate with the outside. The section of these openings shall correspond to at least 200 cm2. Gas connection Make sure that the appliance is adjusted for the gas type available (see the label under the appliance). Follow the instructions indicated in the chapter "gas transformations and adjustments" for the possible adaptation to different gases. The appliance must be connected to the gas system by means of stiff metal pipes or flexible steel pipes having continuous walls, in compliance with the regulations in force. Gas enters the appliance through a cylindrical threaded male gas union (1/2"). The connection must not stress the gas ramp. Once the installation is over, check the connection seal with a soapy solution. Electric connection The appliances without supply cable, does not require to be connected to the mains power supply as it is provided with a low voltage ignition generator supplied by a 1, 5 V battery. 5 15 6 GAS TRANSFORMATIONS AND ADJUSTMENTS Replacing the nozzles If the equipment is adjusted for a type of gas that is different from the one available, it is necessary to replace the burner nozzles. [. . . ] - by means of a straight spanner L, unscrew the nozzle U (fig. 7) and substitute it with the corresponding one. Adjusting the burners The lowest flame point must always be properly adjusted and the flame must remain on even if there is an abrupt shift from the maximum to the minimum position. If this is not so, it is necessary to adjust the lowest flame point as follows: - start the burner up - turn the tap up to the minimum position (small flame) - remove the knob from the tap rod - introduce a flat-tip screwdriver C in the hole F of the tap (fig. 8) and turn the by-pass screw up to a proper adjustment of the lowest flame point. As regards G30 gas burners, the by-pass screw must be tightened completely. 7 8 Replacing the battery (fig. [. . . ]