User manual SONY BDV-E580

[. . . ] WARNUNG Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt. Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung dazu besitzen. ! [. . . ] Attach the two inner rails to both sides (left and right) of unit with the removed screws in the step 6. Tightening torque: 120 x 10 _2 N. m {12. 2 kgf. cm} m . Be sure to use the (B4 x 6) screws when attaching the inner rail. The use other-sized screws may cause a malfunction. Pay attention not to fasten the screws to the screw holes other than actually used screw holes for fixing the inner rails on both sides of the unit. If unnecessary screws are fastened, rack mounting will be unenabled. B4 x 6 Inner rail Inner rail B4 x 6 SRW-5000 1-5 . Remove the four screws from both sides (left and right) of the unit. . Slide the intermediate rail as shown in the figure, and then loosely attach the rail bracket to the outer rail with a plate nut (large) and the two screws. B4 x 6 Plate nut (large) Rail bracket Outer rail Slide B4 x 8 Intermediate rail B4 x 6 n Keep these screws (B4 x 6). Be sure to use these screws when directly fixing the side panels without the rack angles. The use of longer screws such as the screws (PSW 4 x 16) for fixing the rack angles will cause a malfunction of the unit. Attach the two rack angles to both sides (left and right) of the unit with the four screws (PSW4 x 16) supplied with the rack mount kit. While pressing each stopper of inner rails on both sides, slowly push the unit into the rack. c Be careful not to catch your finger or hand in rack mount rail. Ornamental washer RK5 x 14 Stopper RK5 x 14 Intermediate rail Stopper Inner rail Ornamental washer 1-8 SRW-5000 1-7. Matching Connectors and Cables When external cables are connected to the connector of this unit, the hardware listed below (or equivalents) must be used. Panel indication TIME CODE IN AUDIO OUTPUT CUE OUT MONITOR OUTPUT TIME CODE OUT REF. OUT SD OUT AUDIO INPUT (AES/EBU) AUDIO OUTPUT (AES/EBU) REMOTE 2 PARALLEL I/O (50P) REMOTE 1-IN (9P) REMOTE 1-I/O (9P) Matching connector (cable) XLR 3P, MALE XLR 3P, FEMALE Sony part No. 1-508-084-00 1-508-083-00 Remarks BNC 75Z, MALE 1-569-370-12 BNC 75Z, MALE (*1) D-SUB 50P, MALE and JUNCTION SHELL 50P 9P remote control cable (RCC-G series) or D-SUB 9P, MALE and JUNCTION SHEEL 9P D-SUB 9P, FEMALE D-SUB 9P, MALE and JUNCTION SHELL 9P BNC 75Z, MALE (*2) 1-569-370-12 1-565-516-11 1-563-379-11 _ or 1-560-651-00 1-561-749-00 1-563-815-21 1-561-651-00 1-561-749-00 1-569-370-12 RS232C VIDEO CONTROL (9P) HD SDI INPUT HD SDI OUTPUT FORMAT CONV. OUT (OPTION) SD SDI OUT PHONES ETHERNET USB BNC 75Z, MALE (*3) JM-60 stereo phone plug Separately available Separately available 1-569-370-12 _ Upper control panel *1: Coaxial cable length : max. 600 meters (Reference value based on this unit) It is recommended to connect the BELDEN 8281 cable or equivalent to this connector. 100 meters (Reference value based on this unit) It is recommended to connect the BELDEN 1694A cable or equivalent to this connector. 200 meters (Reference value based on this unit) It is recommended to connect the BELDEN 8281 cable or equivalent to this connector. SRW-5000 1-9 1-8. Signal Inputs and Outputs Reduced drawing of rear panel 1 2 3 5 4 Input connectors 1 TIME CODE IN 2 REF. INPUT 2 (OPTION) XLR 3-pin x 1 Time code 0. 5 to 18 V p-p, 10 kZ, balanced BNC x 4 (Loop through output x 2) External reference video signal HD : 0. 6 V p-p, 75 Z, sync negative (HD analog tri-level sync) SD : 0. 3 V p-p, 75 Z, sync negative (Black burst or composite sync) BNC x 6 (1 set : CH1/2, CH3/4, CH5/6, CH7/8, CH9/10, and CH11/12) AES/EBU digital audio Complies with SMPTE 299M, SMPTE 276 (AES-3id-1995) BNC x 1 (outputs the input monitor x 1) Serial digital interface (1. 485 Gbit/s), complies with SMPTE 292M, SMPTE 372M BNC x 1 (outputs the input monitor x 1) Serial digital interface (1. 485 Gbit/s), complies with SMPTE 292M, SMPTE 372M 3 AUDIO INPUT (AES/EBU) 5 HD SDI INPUT A 5 HD SDI INPUT B (OPTION) (Option HKSR-5003) Remote connectors 4 REMOTE 2 PARALLEL I/O (50P) * 4 REMOTE1-IN (9P) 4 REMOTE1-I/O (9P) 4 RS232C 4 VIDEO CONTROL (9P) 4 ETHERNET 4 USB * : Refer to Optional "Interface manual" for details. D-SUB 50P connector D-SUB 9P connector (RS-422A interface), Remote control D-SUB 9P connector (RS-422A interface), Remote control D-SUB 9P connector (RS-232C interface) for ISR (Interactive Status Reporting) D-SUB 9P connector for a HD digital video controller (HKDV-900) connection RJ-45 modular jack Complied with 10BASE-T/100BASE-TX USB series B Complied with USB standard Ver 1. 1 1-10 SRW-5000 Output connectors 1 AUDIO OUTPUT XLR 3-pin x 4 (1 set : CH1, CH2, CH3, and CH4) Analog audio +4 dBm (Standard) (600 Z load), low impedance, balanced XLR 3-pin x 1 Analog audio +4 dBm (Standard) (600 Z load), low impedance, balanced XLR 3-pin x 1 Time code 2. 2 V p-p, low impedance, balanced XLR 3-pin x 2 (1 set : L and R) Analog audio +4 dBm (Standard) (600 Z load), low impedance, balanced BNC x 2 0. 6 V p-p, 75 Z, sync negative (HD analog tri-level sync) BNC x 1 (for character superimpose) Analog composite video VBS : 1. 0 V p-p, 75 Z, sync negative BNC x 1 SYNC (NTSC/PAL) : 0. 286/0. 3 V p-p, 75 Z, sync negative BURST (NTSC/PAL) : 0. 286/0. 3 V p-p, 75 Z, sync negative BNC x 6 (1 set : CH1/2, CH3/4, CH5/6, CH7/8, CH9/10, and CH11/12) AES/EBU digital audio Complies with SMPTE 299M, SMPTE 276M (AES-3id-1995) BNC x 3 (including 1 for character superimpose) Serial digital interface (1. 485 Gbit/s), complies with SMPTE 292M, SMPTE 372M BNC x 3 (including 1 for character superimpose) Serial digital interface (1. 485 Gbit/s), complies with SMPTE 292M, SMPTE 372M BNC x 3 (including 1 for character superimpose) Serial digital interface (270 Mbit/s), complies with SMPTE 259M, ITU-R BT. 656 BNC x 2 (for character superimpose) Serial digital interface (1. 485 Gbit/s), complies with SMPTE 292M JM-60 stereo phone jack Analog audio up to _12 dBu (8 Z load), unbalanced 1 CUE OUT 1 TIME CODE OUT 1 MONITOR OUTPUT 2 HD REF. [. . . ] (Move the knobs to the outside to fix the upper lid (front) assembly. Remove the upper lid (front) assembly. Knob Upper lid (front) assembly Fixing screw Knob Removal Installation SRW-5000 1-23 4. Release the lock of the board holder and open the AE31 board in the arrow direction. Check by eye that the unit is in the state to be able to wind manually the tape. [. . . ]