User manual SONY CDP-997

[. . . ] Model No. CDP-997 Serial No. For customer in the United States CAUTION This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. The use of optical instruments with this product will increase eye hazard. WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] Semi-circles appear around the specified disc numbers in the display. To cancel the selected discs, press DISC 1 ­ 5 again. To return to ALL DISCS Shuffle Play, press PLAY MODE until "ALL DISCS SHUFFLE" appears in the display. · You can select the playing mode by pressing CONTINUE, SHUFFLE, or PROGRAM on the remote. continued 7US Repeat Play Operations You can play the CD tracks repeatedly in any play modes. To activate the Repeat Play function, press REPEAT until "REPEAT' appears in the display. To Press REPEAT Other Operations To Do this Stop playback Pause Select a track Press x. During play or pause, turn lAMSL clockwise (to go forward) or counterclockwise (to go backward) (or press >( to go forward) or . Press the number button on the remote. * Press DISC SKIP. Press and hold M or m during playback, and release at the desired point. Press PLAY MODE until "SHUFFLE" appears in the display. Press ANALOG OUT LEVEL +/­ on the remote. Repeat only one track Until "REPEAT 1" appears while playing the track you want to repeat. Until "REPEAT" or "REPEAT 1" disappears. If you check the order after you start playing, the display shows only the remaining steps. 5 Press H to start Program Play. continued 11US Recording From CDs Programming the CD tracks (continued) Changing the track order You can change your program before you start playing. To You need to Recording a CD by Specifying Tape Length (Time Edit) You can have the player create a program that will fit the length of the tape. The player automatically creates a program, keeping the original order of the disc. The program can contain up to 32 steps (a pause inserted between steps is counted as one step). Note that tracks numbered over 20 cannot be programmed automatically. Erase a track Press CHECK until the track you don't want appears in the display, then press CLEAR. Erase the last track Press CLEAR. Each time you press the button, the last track will in the program be cleared. Add tracks to the end of the program Follow Steps 2 through 4 of the programming procedure. Change the whole Hold down CLEAR until "ALL CLr" appears in the display. program Create a new program following completely the programming procedure. 1 Press DISC SKIP to select the disc. 2 Press TIME EDIT repeatedly before you start playing until "EDIT" appears and "A" in the A indication flashes in the display. Fading In or Out You can manually fade in or out to prevent tracks from starting or ending abruptly. Note that you cannot use this effect when you use the DIGITAL OUT (OPTICAL) connector. To Press FADER 3 Press m or M to specify the tape length. Each time you press these buttons, the display changes as shown below, with the tape length of one side following each indication. C-46 23. 00 - -. - C-54 27. 00 C-90 45. 00 C-60 30. 00 C-74 37. 00 Start play fading in During pause. End play fading out When you want to start fading out. [. . . ] · The player is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the player itself has been turned off. · If you are not going to use the player for a long time, be sure to disconnect the player from the wall outlet. To disconnect the AC power cord (mains lead), grasp the plug itself; never pull the cord. · AC power cord must be changed only at the qualified service shop. · Do not expose the disc to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight as there can be considerable rise in temperature inside the car. [. . . ]