User manual SONY CFD-S500

[. . . ] English Information For customers in the USA This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] · Do not place anything within 10 mm of the side of the cabinet. The ventilation holes must be unobstructed for the player to operate properly and prolong the life of its components. · If the player is left in a car parked in the sun, be sure to choose a location in the car where the player will not be subjected to the direct rays of the sun. · Since a strong magnet is used for the speakers, keep personal credit cards using magnetic coding or spring-wound watches away from the player to prevent possible damage from the magnet. · Do not use solvents such as benzine, thinner, commercially available cleaners or anti-static spray intended for vinyl LPs. · Do not expose the CD to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight as there can be a considerable rise in temperature inside the car. · Do not stick paper or sticker on the CD, nor scratch the surface of the CD. · After playing, store the CD in its case. If there is a scratch, dirt or fingerprints on the CD, it may cause tracking error. Remote The remote does not function. · Replace all the batteries in the remote with new ones if they are weak. · Make sure that you are pointing the remote at the remote sensor on the player. · Remove any obstacles in the path of the remote and the player. · Make sure the remote sensor is not exposed to strong light such as direct sunlight or fluorescent lamp light. · Move closer to the player when using the remote. After trying the above remedies, if you still have problems, unplug the AC power cord and remove all the batteries. After all the indications in the display disappear, plug the power cord and insert the batteries again. If the problem persists, please consult your nearest Sony dealer. Cassette-corder section Recording system 4-track 2 channel stereo Fast winding time Approx. 120 s (sec. ) with Sony cassette C-60 Frequency response TYPE I (normal): 80 - 10 000 Hz 3-238-274-11 (1) Power Sources B C Radio Reception is poor. · Reorient the antenna to improve FM reception. General Speaker Full range: 10 cm dia. , 3. 2 ohms, cone type (2) Outputs Headphones jack (stereo minijack) For 16 - 68 ohms impedance headphones Power output 2. 3 W + 2. 3 W (at 3. 2 ohms, 10% harmonic distortion) Power requirements For CD radio cassette-corder: 120V AC, 60 Hz 9 V DC, 6 size D (R20) batteries For remote control: 3 V DC, 2 size AA (R6) batteries Power consumption AC 20 W Battery life For CD radio cassette-corder: FM recording 1 to AC IN A Connect the AC power cord A or insert six size D (R20) batteries (not supplied) into the battery compartment B . Notes · Replace the batteries when the OPR/BATT indicator dims or when the player stops operating. Replace all the batteries with new ones. Before you replace the batteries, be sure to take out the CD from the player. [. . . ] Press the number buttons to tune in the stored station. To tune in a preset station over 10, press >10 first, then corresponding number buttons. (Example: To tune in a preset station 12, press >10 and 1 first, and then press 2. ) Display D Total track number Total playing time E Programmed track Playing order * For a track whose number is more than 20, the remaining time appears as "- -:- -" in the display. · Adjusting the volume or the audio emphasis will not affect the recording level. · If the AM program makes a whistling sound after you've pressed z in step 3, press MODE to select the position of ISS (Interference Suppress Switch) that most decreases the noise. [. . . ]