User manual SONY FWD-42PV1

[. . . ] 2-581-145-01 (1) FWD-42PV1/42PV1P/42PV1A Flat Panel Display JP Operating Instructions Mode d'emploi Bedienungsanleitung Manual de instrucciones Istruzioni per l'uso GB FR DE ES IT CS FWD-42PV1/42PV1P/42PV1A 2005 Sony Corporation WARNING Owner's Record The model and serial numbers are located on the rear. Record the model and serial numbers in the spaces provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Serial No. To prevent fire or shock hazard, do not expose the unit to rain or moisture. [. . . ] Option1 Component: Selects the signal (component signal) input from the equipment connected to the connectors of the option 1 slot. 640x480/60 Vivid 15 : 07 Picture mode You can switch the input signal using the OPTION button on the display unit. Notes · We recommend input source video equipment equipped with a TBC (time base corrector). If the display receives a signal without TBC, the picture may disappear due to disturbance of the sync signal. · If signals of the same format are input from multiple systems, the Picture Quality setting will default to the most recently set value (Only when the signal formats are identical). 23 (GB) Watching the Picture Input Signal, Picture Mode and Display Status Information Input signal and Picture Mode information appear on the screen for about five seconds when the power is turned on or when the input signal is switched. To disable this function, follow the steps below. 1 2 Press MENU. Press M/m to move the cursor (yellow) to "CUSTOM SETUP" and press ENTER. The CUSTOM SETUP menu appears on the screen. Press M/m to move the cursor (yellow) to "Display" and press ENTER. The following menu appears on the screen. CUSTOM SETUP Power Saving: Speaker Out: Closed Caption: Display: Color Matrix: HD Mode: RGB Mode: Sync Mode: Remote Standard Off Off Off Y/PB/PR On 1080i DTV H/Comp 3 Select Set ENTER Exit MENU 4 Press M/m to set "Display" to "Off, " then press ENTER. To display the information Set "Display" to "On" in step 2 above, then press ENTER. The factory default setting is "On. " Note You can display the input signal information and the time anytime by pressing the DISPLAY button on the Remote Commander, regardless of the above setting. 24 (GB) Watching the Picture Preset input signals Signal name Computer signals 1 3 4 6 VGAa)-1 (VGA 350) b) Color system or horizontal/ vertical frequency 31. 5 kHz 31. 5 kHz 35. 0 kHz 31. 5 kHz 37. 9 kHz 49. 7 kHz 48. 4 kHz 60. 0 kHz 68. 7 kHz 67. 5 kHz 68. 7 kHz 60. 0 kHz 64. 0 kHz 75. 0 kHz 29. 8 kHz 29. 5 kHz 37. 7 kHz 47. 8 kHz 47. 4 kHz 70 Hz 60 Hz 67 Hz 70 Hz 60 Hz 75 Hz 60 Hz 75 Hz 85 Hz 75 Hz 75 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 75 Hz 60 Hz 60 Hz a) VGA is a registered trademark of International Business Machines Corporation, U. S. A. b) VESA is a registered trademark of the Video Electronics Standards Association. c) Mac (Macintosh) is a registered trademark of Apple Computer, Inc. 2 640×480@60 Hz (VESA STD) Macc) 13" VGA (VGA TEXT) Mac 16" Notes 5 800×600@60 Hz (VESA STD) 7 1024×768@60 Hz (VESA STD) 8 1024×768@75 Hz (VESA STD) 9 1024×768@85 Hz (VESA STD) 10 1152×864@75 Hz (VESA STD) 11 Mac 21" 12 1280×960@60 Hz (VESA STD) 13 1280×1024@60 Hz (VESA STD) 14 1600×1200@60 Hz (VESA STD)* 15 848×480@60 Hz (VESA STD)* 16 848×480@60 Hz (VESA STD)** 17 18 19 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 848×480@75 Hz* 1280×768@60 Hz 1280×768@60 Hz SDTV/HDTV PAL NTSC SECAM NTSC4. 43 PAL60 PAL-M PAL-N 575/50i 480/60i 1080/24psf 1080/50i 576/50p 480/60p 1080/60i 720/60p · When inputting an HDTV signal, input the tri-level sync signal to the 2nd pin of RGB/COMPONENT (D-sub 15 pin) on the INPUT2 connector or the BKM-FW12. · If colors appear too light after inputting a DVD signal to the display unit, adjust the "Chroma" setting in the Adjust Picture menu. · When the phase is readjusted, the resolution will be reduced. · You cannot input the signal indicated with * to DVI IN. · You cannot input the signal indicated with ** to an analog RGB input connectors. Actual on-screen display of the unit's status On-screen display Significance The selected input signal is computer RGB. The selected input signal is component video. The input signal is out of the capture range. The signal mode of INPUT1 is set to digital RGB. The signal mode of INPUT2 is set to analog RGB. The signal mode of INPUT2 is set to component video. The signal mode of Option 1 slot is set to composite video. The signal mode of Option 1 slot is set to S VIDEO. [. . . ] The indicator flashes (with an image showing on the display) or flashes at intervals of three seconds (with no image showing on the display). Count the number of flashes if the indicator flashes at intervals of three seconds. For example, the indicator flashes twice, followed by a three second pause, two more flashes and this pattern repeats. In this case, the count for the number of flashes is two. [. . . ]