User manual SONY HCD-EC55

[. . . ] 2-899-084-11(1) NOTICE FOR THE CUSTOMERS IN THE U. S. A. CAUTION Mini Hi-Fi Component System Operating Instructions Owner's Record The model and serial numbers are located on the rear of the unit. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product. ______________ You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems) Basic Operations * Adjusting the sound To adjust the volume Press VOLUME +/­ on the remote (or turn the VOLUME control on the unit) . Notes on playing multisession discs If the disc begins with a CD-DA (or MP3) session, it is recognized as a CD-DA (or MP3) disc, and playback continues until another session is encountered. [. . . ] 4 Press / (or / on the unit) 2 Prepare the recording source. Select the desired source to record. Place the disc you want to record and press DISC SKIP/EX-CHANGE to select a disc. When recording a folder from an MP3 disc, press PLAY MODE repeatedly to select " , " and then press +/­ repeatedly to select the desired folder. To record only your favorite CD tracks or MP3 files in your desired order, perform steps 2 to 5 of "Creating your own CD program. " repeatedly until the desired track number appears. When programing MP3 files, press +/­ repeatedly to select the desired folder, and then select the desired file. Selected track or file number Immediately unplug the power cord, and check the following item. If your system has a voltage selector, is the voltage selector set to the correct voltage?After the STANDBY indicator on the unit stops flashing, reconnect the power cord, and turn on the system. If the issue persists, contact your nearest Sony dealer. If the STANDBY indicator flashes to display the clock and then press while holding down on the unit. With CD player power turned off, disc access time is increased. To turn on CD player power, repeat the procedure until "CD POWER ON" appears. To reset the system to factory settings Before playing, wipe the disc with a cleaning cloth from the center out to the edge. Do not clean discs with solvents, such as benzine thinner, or commercially available cleaners or antistatic spray intended for vinyl LPs. Do not expose discs to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight. Powerconsumption: MHC-GX99 USA model: 190 W Canadian model: 245 VA USA model: 115 W Canadian model: 155 VA USA model: 190 W Canadian model: 245 VA European and Russian models: 140 W 0. 5 W (in Power Saving Mode) Other models: 150 W USA model: 95 W Canadian model: 130 VA European and Russian models: 95 W 0. 5 W (in Power Saving Mode) Other models: 95 W Approx. 200 × 306 × 410 mm If the system still does not operate properly, reset the system to factory settings. Use buttons on the unit to reset the unit to its factory default settings. On safety 1 Disconnect and reconnect the power cord, and then turn on the system. 2 Press PLAY MODE , FUNCTION , and at General The system does not turn on. Is the power cord plugged in? Is the voltage selector set correctly to match the local power line voltage?Saudi Arabian models also may not turn on when the voltage selector is set to NO OPERATION. 3 Start recording. Total playing time of the selected track the same time. All user-configured settings, such as preset radio stations, timer, and the clock, are deleted. 5 Press ENTER to add the track or file to the program. 6 Repeat steps 3 through 5 to program additional tracks or files, up to a total of 25 tracks or files. Press (record) , and then start playing the desired recording source. The CD starts playing automatically after 10 seconds have passed. If there is noise while recording from the tuner, reposition the appropriate antenna to reduce the noise. While recording, you cannot listen to other sources. The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off. Completely disconnect the power cord (mains lead) from the wall socket (mains) if it is not going to be used for an extended period of time. When unplugging the unit, always grip the plug. [. . . ] The preset stations are retained for about half a day even if you disconnect the power cord or if a power failure occurs. The following discs take a longer time to start playback. a disc recorded with a complicated tree structure. a disc that has not been finalized (a disc to which data can be added). a disc that has many folders. System: Compact disc and digital audio system Laser: Semiconductor laser (=770 ­ 810 nm) Emission duration: continuous Frequency response: 20 Hz ­ 20 kHz Signal-to-noise ratio: More than 90 dB Dynamic range: More than 88 dB Tapedecksection(ExceptforNorthAmericanmodel) Recording system: 4-track 2-channel, stereo Tunersection 5 Use the same procedure as in step 4 to set the time to stop playing. The disc tray does not open and "LOCKED" appears. To later reuse the tape for recording, cover the broken tab with adhesive tape. FM stereo, FM/AM superheterodyne tuner Antenna: FM lead antenna AM loop antenna FM tuner section: Tuning range North American model: 87. 5 ­ 108. 0 MHz (100 kHz step) Other models: 87. 5 ­ 108. 0 MHz (50 kHz step) Intermediate frequency: 10. 7 MHz AM tuner section: Tuning range Pan-American and Australian models: 530 ­ 1, 710 kHz (with 10 kHz tuning interval) 531 ­ 1, 710 kHz (with 9 kHz tuning interval) European, Russian and Saudi Arabian models: 531 ­ 1, 602 kHz (with 9 kHz tuning interval) Other models: 530 ­ 1, 610 kHz (with 10 kHz tuning interval) 531 ­ 1, 602 kHz (with 9 kHz tuning interval) Intermediate frequency: 450 kHz 6 Select the sound source. Press / repeatedly until the desired sound source appears, and then press ENTER . [. . . ]