User manual SONY KDL-46NX800

[. . . ] 4-178-676-16(1) LCD Digital Color TV Setup Guide (Operating Instructions) Setting up your TV To watch TV Additional Information Sony Customer Support U. S. A. : www. sony. com/tvsupport Canada: www. sony. ca/support United States 1. 800. 222. SONY Canada 1. 877. 899. SONY Please Do Not Return the Product to the Store KDL-60NX801 / 60NX800 / 52NX801 / 52NX800 / 46NX800 / 46NX700 / 40NX700 Owner's Record The model and serial numbers are located on the side and rear of the TV. For KDL­NX800 series models, they can be found by removing the bottom cover. Record these numbers in the spaces provided below. Refer to them whenever you call upon your Sony dealer regarding this TV. In the United States, TV Guide and TV Guide On Screen are registered trademarks of TV Guide Entertainment Group, Inc. [. . . ] · Never install the TV on: ­ slippery, unstable and/or uneven surfaces. ­ furniture that can easily be used as steps, such as a chest of drawers. · Install the TV where it cannot be pulled, pushed, or knocked over. · Route all AC power cords and connecting cables so that they are not accessible to curious children. Stand 2 Secure the TV to the Stand. Recommended Measures to Secure the TV Consider the following measures when securing your TV to a TV stand (not supplied). Use the optional hardware listed below (not supplied): · M4 × 16 machine screw (screwed into the TV's Table-Top Stand) · A screw or similar (attach it to the TV stand) · Rope or chain (strong enough to support the weight of the TV). Make sure that there is no excess slack in the rope or chain. An alternative way to secure the TV is with an optional Sony Support Belt Kit. M4 × 16 machine screw (not supplied) Screw hole on the Table-Top Stand Rope or chain (not supplied) Screw (not supplied) ~ Contact Sony Customer Support to obtain the optional Support Belt Kit by providing your TV model name. · For United States call: 1-800-488-7669 or visit: www. sony. com/accessories · For Canada call: 1-877-899-7669 12 3 Anchor the TV to the Wall. Anchor the TV to the wall by using bolts, wall anchor and chain (or rope). ~ · Your TV is shipped with screws attached to the rear of the TV. (They are fastened in the screw holes for wall mounting. ) Be sure to remove the upper two screws prior to anchoring the TV on a wall. · Securing the TV to the stand without securing the TV and the stand to the wall provides minimum protection against the TV toppling over. For further protection, be sure to follow the three measures recommended. Anchor bolts (not supplied) Organizing the AC power cord Setting up your TV ~ · After the AC power cord is thread as illustrated, place the bottom cover (for NX800 series only). Wallmount holes Rope or chain (not supplied) Wall-anchor (not supplied) 13 Running initial setup Detaching the Table-Top Stand from the TV Remove only the screws marked with the TV. on ~ · The NX700/NX800 series models must remove the stand rear cover prior to detaching the TableTop Stand. · Do not remove the Table-Top Stand for any reason other than to install corresponding accessories on the TV. · When installing the TV on a wall, remove the four screws from the rear of the TV. (They are fastened in the screw holes for wall mounting. ) Be sure to store the removed screws in a safe place, keeping them away from children (for KDL-60/52NX801 and KDL-60/52/46NX800 models). · When attaching the Table-Top Stand again, be sure to fasten the four screws (previously removed) to the original holes on the rear of the TV (for KDL-60/52NX801 and KDL-60/52/ 46NX800 models). 1 2 3 Complete your cable connections before proceeding with the Initial Setup. Connect the TV to your nearest power outlet. Check the ENERGY SAVING SWITCH setting is on (z). When you switch the TV on for the first time, the Language menu appears on the screen. ~ · The TV image shown here may differ from your TV but the operation of your TV remains the same as indicated. 4 Follow the instructions on the screen. ~ · The ENERGY SAVING SWITCH must be on (z) to set the clock and obtain program information for the TV Guide. · Home mode sets the TV to display the settings optimized for home viewing (this setting is ENERGY STAR compliant). 5 Select Continue to scan for available channels and enable the TV Guide On Screen® feature. If you receive channels from a cable box or satellite receiver and do not wish to use the TV's built-in tuner, select Skip. Selecting Skip will disable the TV Guide On Screen feature, which is only available when the TV's tuner is used. ~ · If you skip the channel scan while in the setup menus, TV Guide will be disabled. 14 Using a Wall-Mount Bracket Your TV can be mounted on a wall using a Wall-Mount Bracket (not supplied) out of the box as packaged. Some larger size TV may require detaching the Table-Top Stand; see "Detaching the Table-Top Stand from the TV" (page 14). [. . . ] · Design and specifications are subject to change without notice. 20 Declaration of Conformity Trade Name: SONY Model: KDL-60NX801/KDL-60NX800/KDL-52NX801/ KDL-52NX800/KDL-46NX800/KDL-46NX700/ KDL-40NX700 Responsible Party: Sony Electronics Inc. Address: 16530 Via Esprillo, San Diego, CA 92127 U. S. A. Telephone Number: 858-942-2230 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device uses 5 GHz band for wireless LAN communication and the maximum gain of the antenna in this device is 6 dBi. [. . . ]