User manual SONY KDL32EX402AEP

[. . . ] Intel® Desktop Board DP55SB Technical Product Specification September 2009 Order Number: E70714-001US The Intel® Desktop Board DP55SB may contain design defects or errors known as errata that may cause the product to deviate from published specifications. Current characterized errata are documented in the Intel Desktop Board DP55SB Specification Update. Revision History Revision -001 Revision History First release of the Intel Desktop Board DP55SB Technical Product Specification ® Date September 2009 This product specification applies to only the standard Intel® Desktop Board DP55SB with BIOS identifier KGIBX10J. Changes to this specification will be published in the Intel Desktop Board DP55SB Specification Update before being incorporated into a revision of this document. [. . . ] Furthermore, improper connection of USB or 1394 header single wire connectors may eventually overload the overcurrent protection and cause damage to the board. This section describes the board’s connectors. The connectors can be divided into these groups: • • Back panel I/O connectors Component-side I/O connectors and headers (see page 43) 41 Intel Desktop Board DP55SB Technical Product Specification 2. 1 Back Panel Connectors Figure 10 shows the location of the back panel connectors for the board. Item A B C D E F G H I J K L M N O Description eSATA port Back-to-BIOS button S/PDIF in (optical) S/PDIF out (optical) USB ports IEEE 1394a connector USB ports LAN USB ports Surround left/right channel audio out Side Surround Center channel and LFE (subwoofer) audio out Audio line in/(Side Surround) audio out Front left/right channel audio out/Two channel audio line out Mic in Figure 10. Back Panel Connectors NOTE The back panel audio line out connector is designed to power headphones or amplified speakers only. Poor audio quality occurs if passive (non-amplified) speakers are connected to this output. 2 Component-side Connectors and Headers Figure 11 shows the locations of the component-side connectors and headers. 0 x16 connector Vertical USB connector Processor core power connector (2 x 4) Processor fan header Main power connector (2 x 12) Front panel header Back panel CIR emitter (output) header Front panel CIR receiver (input) header Alternate front panel power LED header Front chassis fan header USB 2. 0 header IEEE 1394a front panel header SATA connectors Chassis intrusion header Auxiliary PCI Express graphics power connector (SATA-style) 44 Technical Reference 2. Processor, Front and Rear Chassis (4-Pin) Fan Headers Pin 1 2 3 4 Note: Signal Name Ground (Note) +12 V FAN_TACH FAN_CONTROL These fan headers use Pulse Width Modulation control for fan speed. Back Panel CIR Emitter (Output) Header Pin 1 2 3 4 5 6 Signal Name Emitter out 1 Emitter out 2 Ground Key (no pin) Jack detect 1 Jack detect 2 Table 21. 2 • Add-in Card Connectors The board has the following add-in card connectors: PCI Express 2. 3 • Power Supply Connectors The board has the following power supply connectors: Main power – a 2 x 12 connector. This connector is compatible with 2 x 10 connectors previously used on Intel Desktop boards. The board supports the use of ATX12V power supplies with either 2 x 10 or 2 x 12 main power cables. When using a power supply with a 2 x 10 main power cable, attach that cable on the rightmost pins of the main power connector, leaving pins 11, 12, 23, and 24 unconnected. processor core power – a 2 x 4 connector. This connector provides power directly to the processor voltage regulator and must always be used. Failure to do so will prevent the board from booting. Auxiliary PCI Express graphics power connector (SATA style) – this connector provides the required additional power when using high power (75 W or greater) add-in cards in either or both the PCI Express x16 and the PCI Express x8 bus add-in card connectors. €¢ • CAUTION If high power (75 W or greater) add-in cards are installed in either or both the Secondary PCI Express x16 and the PCI Express x4 bus add-in card connectors, the Auxiliary PCI Express graphics power connector must be used. [. . . ] 2 Recycling Considerations As part of its commitment to environmental responsibility, Intel has implemented the Intel Product Recycling Program to allow retail consumers of Intel’s branded products to return used products to selected locations for proper recycling. Com/intel/other/ehs/product_ecology for the details of this program, including the scope of covered products, available locations, shipping instructions, terms and conditions, etc. This Intel Desktop Board is lead free although certain discrete components used on the board contain a small amount of lead which is necessary for component performance and/or reliability. This Intel Desktop Board is referred to as “Lead-free second level interconnect. [. . . ]