User manual SONY MDS-501

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. [. . . ] If you entered the wrong track number Press m/M repeatedly until the wrong track number flashes, then do step 3 above again. To enter a track number over 10 Z Use >10. To check the total playing time of the program Press LEVEL/DISPLAY/CHAR (or DISPLAY). 4 Repeat step 3 to enter other tracks. 25 Creating Your Own Program (Program Play) Tips for Recording From MDs to Tape MENU/NO AMS YES Changing the contents of the program While the deck is stopped and "PROGRAM" lights up, do steps 1 and 2 of "Programming the tracks" on page 25, followed by one of the procedures below: To Erase a track `/1 Z N X x z . > Do the following: Press m/M repeatedly until the number of the unwanted track flashes, then press CLEAR. Press CLEAR repeatedly until all the track numbers disappear. Press m repeatedly until "0" flashes before the first track number, then do steps 3 to 5 of "Programming the tracks" on page 25. Press m/M repeatedly until the track number which will precede the new track flashes. Press AMS to display flashing "0, " then do steps 3 to 5 of "Programming the tracks" on page 25. Press M repeatedly until "0" flashes after the last track number, then do steps 3 to 5 of "Programming the tracks" on page 25. Press m/M repeatedly until the number of the track to be changed flashes, then do steps 3 to 5 of "Programming the tracks" on page 25. m M Erase all tracks Add a track at the beginning of the program Inserting blanks between tracks during play (Auto Space) The MD deck can be set to automatically insert a threesecond blank between tracks during play. This function is useful when you're recording from an MD to an analog tape since the three-second blank enables you to use the Multi-AMS function later to locate the beginning of tracks on the tape. Playing MDs Add a track in the middle of the program 1 2 3 Add a track to the end of the program While the deck is stopped, press MENU/NO twice. "Setup Menu" appears in the display. Example: Erasing the second track 1 AAA 2 BBB 3 CCC 4 DDD 1 AAA 2 CCC 3 DDD When you erase a track, all the tracks after the one erased are automatically renumbered. For example, if you erase track number 2, the previous track number 3 becomes track number 2 and the previous track number 4 becomes track number 3, and so on. Editing Recorded MDs 1 While the deck is stopped, playing, or paused, press MENU/NO. "Edit Menu" appears in the display. Turn AMS (or press . /> repeatedly) until "Tr Erase ?" appears, then press AMS or YES. The deck starts to play the track indicated by the number in the display. Turn AMS (or press . /> repeatedly) until the track number you want to erase appears. "Complete!!" appears for a few seconds and the track is erased. The track following the erased track starts to play. If the erased track is the last one on the MD, the track preceding the erased track starts to play. 2 3 4 To cancel the operation Press MENU/NO or x. z If "Erase ???" appears in step 4 above The track has been record-protected on another MD deck. If you still want to erase the track, press AMS or YES again while the indication appears. z To avoid confusion when erasing more than one track Start erasing from the highest numbered track. This way you'll avoid renumbering the tracks that you plan to erase. z You can undo the erasure For details, see "Undoing the Last Edit" on page 36. 29 Erasing Tracks Erasing all the tracks on an MD Do the procedure below to erase all the tracks, track names, and disc name at once. 4 1 While the deck is stopped, playing, or paused, press MENU/NO. [. . . ] Should the problem persist, consult your nearest Sony dealer. Three-digit code/Message C11/Protected C13/REC Error Cause/Remedy The inserted MD is record-protected. , Take out the MD and close the record-protect slot (page 15). , Set the deck in a stable surface, and repeat the recording procedure. [. . . ]