User manual SONY NVA-B20N DATASHEET

[. . . ] After a short time, the following display or a similar display appears. VTVV ! Using the right rotary control select, "!The navigation and radio software is updated. During updating, the ignition should be switched on and the vehicle should not be moved. Note on update for 4725/26 (blue display) After starting an update, the display illumination is switched off during installation. [. . . ] Requesting current position During route guidance, the current position can be requested. QFV P Press the multifunction button .  ° n ° n ! Press the multifunction button . ° n ° n ! The current position with road name (if available), degrees of longitude and latitude, altitude above sea level and the number of satellites received are displayed. Pressing the right rotary control or the 1DY button returns to the information menu. The current position with road name (if available), degrees of longitude and latitude, altitude above sea level and the number of satellites received are displayed. Pressing the right rotary control returns to the navigation display. By pressing the right rotary control , the program returns to the route guidance display. For inactive route guidance, the information menu can be requested by pressing the left rotary control . Subject to errors and technical modifications 26 Copyright by Becker GmbH, D-76303 Karlsbad Navigation CD 8. X Points of interest (P. O. I. ) CD The following contains the general description of the points of interest (or P. O. I. ) CDs. There are two methods of selecting a point of interest from a points of interest (P. O. I. ) CD: - During active navigation, a point of interest can be selected in the vicinity of the current position or near the entered destination. - If navigation is not active, points of interest can be selected in the vicinity of the current position. Insert the desired points of interest CD into the CD slot. After a short time, the following display appears:    J # !! Select the desired category with the right rotary control . Nevertheless, some data may be incorrect or outdated. Under no circumstances do we accept any liability. Pressing 1DY or pressing the left rotary control , returns to the list of points of interest. Following selection of the point of interest, you are prompted to insert the navigation CD for route calculation. If the point of interest was selected during active navigation, it will be treated as a stopover. Subject to errors and technical modifications 28 Copyright by Becker GmbH, D-76303 Karlsbad Navigation CD 8. X Influencing the calculation of ETA "!! Setting the time display !  !"! T The distance to the next point at which for example a turn should be made is displayed below the navigation arrow, which appears in reduced format. On routes with variable speed limits (dependent on weather conditions, time of day etc. ) a symbol with the text @5Y or a speed with an underscore (e. g. : "80") draws the driver's attention to the fact that the speed limit is variable. due to road works) are usually short-lived, these have not been included on the CD.  ! !! Set and confirm ! in the System Settings menu. F By pressing the right rotary control selection can be made between speed limits display or . Setting is confirmed and accepted by pressing and holding the right rotary control . Subject to errors and technical modifications 30 Copyright by Becker GmbH, D-76303 Karlsbad Navigation CD 8. X Dynamic navigation with TMC Note: Dynamic route guidance is not possible in all countries. To use dynamic navigation and the functions described below, TMC must be switched on, as described under "Switching TMC on/off" on page 36. [. . . ] The functionality of the traffic programme functions depends on the status of the TMC setting - TMC switched on/off ("Switching TMC on/off" on page 36) When TMC is switched off: · There are two ways to select a TP transmitter: - automatic tracking - direct programming Automatic tracking always uses the FM station currently being received as the TP transmitter. If the selected FM station has poor reception quality or cannot function as a TP transmitter, the unit applies specified criteria to search for a new TP transmitter. Direct programming enables a TP transmitter to be programmed that is not the FM station being received. For ex34 If an RDS transmitter is equipped with a traffic programme, this is indicated on the display by ! [. . . ]