User manual SONY NVA-CU3 NOTICE FOR SUPPLIED CAR BATTERY ADAPTER XA-DC2

[. . . ] After a short time, the following display or a similar display appears. VRVV ! Using the right rotary control select , %"!The navigation and radio software is updated. During updating, the ignition should be switched on and the vehicle should not be moved. 1RWH RQ XSGDWH IRU EOXH GLVSOD\ After starting an update, the display illumination is switched off during installation. [. . . ] If there is no correspondence, the categories are displayed in all available languages. This can be recognised by the country abbreviations in front of the category. If the points of interest CD is inserted during active navigation, the system requests information on the location of the point of interest (near to destination or in vicinity of current position). If navigation is not active, this selection is skipped. The arrows following the distance information indicate the direction of the relevant point of interest (e. g. point of interest lies in the direction of travel, point of interest lies in the opposite direction to that of travel). Then, turn the right rotary control to select the desired point of interest. The point of interest is accepted by pressing the rotary control . Before confirming the point of interest, press 1DY to return to selection of categories in order to select a different point of interest, if required. Press the left rotary control to display information on the point of interest. This information may include prices, location description, general appraisal etc. , for the point of interest. "! !! With the right rotary control, select either !!. or !  !# OHM q After a short time, the available points of interest for the selected categories are displayed. Pressing 1DY or pressing the left rotary control , returns to the list of points of interest. To use dynamic navigation and the functions described below, TMC must be switched on, as described under "Switching TMC on/off" on page 30. When any route recalculations are made with active dynamic route guidance, the navigation system may request the Navigation CD (if the Navigation CD is not already inserted). 1RWH Can only be selected if TMC has been switched on or is currently switched on. See "Switching TMC on/off" on page 30. # !! D F F " Y If !!S&Y !!S !"! is not displayed immediately (display or !!S !Y), then & must be selected by entering the route settings. Y Y :KDW LV G\QDPLF URXWH JXLGDQFH" Dynamic route guidance is used to calculate the route, taking current traffic announcements into account. The traffic announcements are transmitted by a TMC radio station in addition to the radio programme and are received and analysed by the navigation system. There is no charge for receiving traffic announcements. 1RWH Traffic announcements are transmitted by radio stations, therefore we cannot accept any responsibility for the completeness and correctness of the announcements $FWLYDWLQJ G\QDPLF URXWH JXLGDQFH Dynamic route guidance can be started by selecting !!S&Y Y in the route menu. !"! Dynamic route guidance is started after confirmation of using the right rotary control and subsequent confirmation of !!S&Y Y. & " ! Subject to errors and technical modifications 25 Copyright by Becker GmbH, D-76303 Karlsbad 1DYLJDWLRQ &' ; 1RWH If dynamic route guidance has been activated, the routes are calculated using the "fast route" setting. 'LVSOD\LQJ WUDIILF LQIRUPDWLRQ Current traffic announcements can be displayed in plain text. [. . . ] The functionality of the traffic programme functions depends on the status of the TMC setting - TMC switched on/off ("Switching TMC on/off" on page 30) When TMC is switched off: · There are two ways to select a TP transmitter: DXWRPDWLF WUDFNLQJ GLUHFW SURJUDPPLQJ $XWRPDWLF WUDFNLQJ always uses the FM station currently being received as the TP transmitter. If the selected FM station has poor reception quality or cannot function as a TP transmitter, the unit applies specified criteria to search for a new TP transmitter. 'LUHFW SURJUDPPLQJ enables a TP transmitter to be programmed that is not the FM station being received. For ex28 If an RDS transmitter is equipped with a traffic programme, this is indicated on the display by ! [. . . ]