User manual SONY RC-202IPV

[. . . ] And don't place lighted candles on the apparatus. To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the apparatus. Don't throw away the battery with general house waste, dispose of it correctly as chemical waste. CAUTION You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. WARNING This appliance is classified as a CLASS 1 LASER product. This label is located on the rear exterior. [. . . ] · Recording automatically stops if recording is paused for more than about 3 minutes. Useful Tips for Recording When using the remote, set SELECT to CDR. SBM TIME SELECT TIME Checking the remaining recordable time on the CD-R or CD-RW Press TIME repeatedly. · Each time you press the button while the unit is stopped, the display alternates between total disc playing time and remaining recordable time on the CD-R or CD-RW (page 9). · Each time you press the button while recording, the display alternates between the recording time of the current track and the remaining recordable time on the CD-R or CD-RW (page 10). Note on a copy protection Some commercial CD may contain a copy protection code that will prevent the disc from being recorded. In this case, "Cannot Copy" and either "C12" or "C41" will appear alternately in the display. Do not move the unit or disconnect the unit from power source in the following situation. Recording may not complete successfully. · When "Finalize, " "Unfinalize, " "Erase, " or "OPC" appears in the display: The unit is currently updating the table of contents (TOC). · When "PMA Writing" appears in the display: The unit is currently updating the track information. 16 If "Auto Cut" appears in the display (Auto Cut Function) There has been no sound input for about 30 seconds during recording. The 30 seconds of silence are replaced by a blank of about 3 seconds and the unit changes to recording pause. If the unit continues pausing for about 3 minutes after the Auto Cut Function activated, recording stops automatically. Note that this function does not activate if the unit has started recording from a blank portion or is synchro-recording from a CD on DECK A. Tip Insert the silence into the end of the song (The function of adding Post Gap) You can insert the silence of 2 seconds between the songs, when recording more than two tracks at once. The silence is inserted according to the following situations. · When the disc of DECK A changes to the next disc during Synchro-Recording. High speed recording changes to normal speed recording. For detailed explanation on SCMS, refer to the "Notes" on page 20. · When copying a commercial music CD contains copy protection code, the unit automatically select the analog recording. High speed recording changes to normal speed recording. · You cannot stop recording during finalizing in Make-Disc Synchro-Recording. Normal speed SynchroRecording The disc is recorded at the same speed as the playing CD. You can hear the sound during recording. When using the remote, set SELECT to CDR. DISC 1-5 A POWER (OPEN/CLOSE for RCD-W10) OPEN/CLOSE You can perform Synchro-Recording in the programmed order (page 15). Make-Disc Synchro-Recording (MAKE DISC) Records a CD in the original order of its track number regardless of the selected play mode, and finalizes the disc. Be sure to use the disc that has not been recorded. ("Blank Disc" appears in the display when you put the disc in DECK B. ) · A CD text (if contained in the disc) is automatically recorded. (Note that "Text Save" in Setup Menu is set to "On. " ) You can enter the disc name or track name (up to 70 characters each, and 40 tracks per disc). Tip CD SYNCHRO NORMAL xH SELECT When you do not want to record the CD text automatically, set "Text Save" in Setup Menu to "Off. " For details, see "Using the Setup Menu" (page 28). Depending on the CDs, the CD text is automatically recorded even if "Text Save" in Setup Menu is set to "Off. " H CD SYNCHRO NORMAL x 18 1 Press POWER. [. . . ] It is caused by the digital signal during recording. During recording of a digital sound source, the connecting cable has been disconnected or the player of the sound source has turned off. · Connect the cable or turn on the digital player. 30 Troubleshooting If you experience any of the following difficulties while using the unit, use this troubleshooting guide to help you remedy the problem. The sound has a lot of static. Strong magnetism from a television or a similar device is interfering with operations. Move the unit away from any sources of strong magnetism. Other No sound is output. DECK A (the CD player section) The player does not start playing. · Make the connections properly (page 6). [. . . ]