User manual SONY RDP-XF300IP

[. . . ] Should you notice an abnormality in the unit, disconnect the main plug from the AC outlet immediately. The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off. The nameplate and important information concerning safety are located on the bottom exterior of main unit and on the surface of AC power adaptor. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems) AUDIO IN DC IN 20V Features iPod/iPhone compatible MEGA BASS Audio in function Wireless remote commander supplied To wall outlet AC power adaptor Note on the AC power adaptor AC power cord Precautions Play the unit on the power source specified in "Specifications. " To disconnect the AC power cord (mains lead), pull it out by the plug, not the cord. [. . . ] When the remote commander no longer operates the unit, replace the battery with a new one. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ­ Reorient or relocate the receiving antenna. ­ Increase the separation between the equipment and receiver. ­ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ­ Consult the dealer or an experienced radio/TV technician for help. NOTES ON LITHIUM BATTERY Wipe the battery with a dry cloth to assure a good contact. Be sure to observe the correct polarity when installing the battery. Do not hold the battery with metallic tweezers, otherwise a short-circuit may occur. with the + side facing up If you have any questions or problems concerning your unit, please consult your nearest Sony dealer. Notes WARNING Replace the battery for the remote commander with a Sony CR2025 lithium battery. Use of another battery may present a risk of fire or explosion. 4 Input AUDIO IN jack (ø 3. 5 mm stereo minijack) Power output 20 W + 20 W (at 1% harmonic distortion) External power source DC IN 20V Dimensions Approx. 356. 0 mm × 158. 1 mm × 151. 9 mm (w/h/d) (14 1/16 inches × 6 1/4 inches × 6 inches) Mass Approx. 1. 32 kg (2 lb 15 oz) Supplied accessories Remote commander (1) AC power adaptor (1) AC power cord (1) Audio connecting cable (1) Universal Dock Adapter for iPhone (1) Universal Dock Adapter for iPhone 3G & iPhone 3GS (1) Design and specifications are subject to change without notice. Make sure the iPod is connected firmly. Make sure the iPod is connected firmly. Operation is not performed. Remote sensor To use this unit as a battery charger for your iPod The iPod cannot be charged. You can use the unit as a battery charger for your iPod. Charging begins when the iPod is connected to the unit. The charging status appears in the iPod display. For details, see the user's guide of your iPod. Audio in Make sure the Audio connecting cable is connected firmly. Remote Tip Remove the case or cover from your iPod before setting it in the tray to ensure a stable connection. Connecting optional components You can enjoy the sound from an optional component such as a portable digital music player through the speakers of this unit. Be sure to turn off the power of each component before making any connections. For details, refer to the instruction manual of the component to be connected. The remote does not function. 3 Press (direct power-on). The iPod begins to play back. You can operate the connected iPod by this unit or the iPod buttons. Docking Tray Replace the battery in the remote commander with a new one if it is weak. Make sure that you are pointing the remote at the remote sensor on the unit. [. . . ] If you are using an iPhone, iPhone 3G or iPhone 3GS, attach the supplied universal dock adapter for iPhone, iPhone 3G or iPhone 3GS before connecting. The adapter number, or , is shown on the underside of the supplied universal dock adapters. is for the iPhone, and is for iPhone 3G & iPhone 3GS. Universal Dock Adapter Locate a point while (forward) or observing the iPod display (backward) in pause and hold it until you find the point then press . [. . . ]