User manual SONY RM-AX4000A

[. . . ] Integrated Remote Commander Operating Instructions Getting Started Operating Unit Settings Setting by On-Remote Setup Additional Information Appendix RM-AX4000A RM-AX4000 This manual explains two models, RM-AX4000A and RM-AX4000. On the model RM-AX4000A, the supplied software "AX Remote Editor" is updated. © 2005 Sony Corporation WARNING To reduce the risk fire or electric shock, do not expose this apparatus to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Owner's Record The model number is located on the rear of the unit and the serial number is located in the battery compartment. [. . . ] The buttons to activate backlight changes and a beep sounds each time you press the keys. Note In the "ALL" position, if you use the Remote Commander frequently, the battery life may be shorter. In this case, shorten the automatic-off time. 10 Press the ON or OFF key to select the fade effect of the backlight. ON: fade in/out backlight OFF: normal backlight The fade effect of the backlight changes and a beep sounds each time you press the keys. 11 Press the BACK button or the COMMANDER OFF button. BACK COMMANDER OFF or "LIGHT" appears as the Display title. SU LEARN NG LIGHT 14 Press the BACK button or the COMMANDER OFF button. BACK COMMANDER OFF or OFF_TIME LEVEL FADE ON_MODE "LIGHT" appears as the Display title. SU LEARN NG LIGHT 12 Press "ON_MODE" on the Label keys. ON_MODE OFF_TIME LEVEL FADE ON_MODE The setting display for buttons to activate the backlight appears. The current setting is shown inside the [ ], while the other flashes. SU 15 Press and hold the COMMANDER OFF button for more than 2 seconds. COMMANDER OFF LEARN NG LIGHT The Remote Commander turns off. ON_MODE LIGHT [ ALL ] 36 If you want to quit before finishing Press and hold the COMMANDER OFF button for more than 2 seconds. The previous status returns, and the Remote Commander turns off. Setting the LCD display Setting the automatic-off time of the LCD display The Remote Commander is preset at the factory to switch off the LCD display automatically if you do not operate it for more than 5 minutes. To change this setting, perform the following procedure. If you want to return to the previous display Press the BACK button or the COMMANDER OFF button. 1 While pressing the COMMANDER OFF button, press the MUTING button. COMMANDER OFF MUTING "SET" appears as the Display title. SU LEARN NG SET LIGHT DISPLAY OTHER Unit Settings If "DISPLAY" does not flash on the Label keys, press the Display title (SET) repeatedly until it appears. Continued 37 Setting the LCD display (continued) 5 Press and hold the COMMANDER OFF button for more than 2 seconds. COMMANDER OFF 2 Press "DISPLAY" on the Label keys. DISPLAY The Remote Commander turns off. "DISPLAY" appears as the Display title. SU If you want to quit before finishing Press and hold the COMMANDER OFF button for more than 2 seconds. The previous status returns, and the Remote Commander turns off. LEARN NG DISPLAY If you want to return to the previous display DISP-OFF ALIGN CONTRAST Press the BACK button or the COMMANDER OFF button. 3 Press "DISP-OFF" on the Label keys. DISP-OFF The setting display for automatic-off time of the LCD display appears. SU LEARN NG DISPLAY DISP-OFF (-) 05min (+) 4 Press the (­) or (+) key to change the automatic-off time of the LCD display. You can set the automatic-off time from 1 to 30 minutes. Each time the (­)/(+) key is pressed, the minute decreases/increases by 1 minute. For example, "02min" on the Label keys means 2 minutes. 38 Calibrating the alignment of the LCD display You can calibrate the alignment of the LCD display if the Touch-keys are not working properly. To change this setting, perform the following procedure. 3 Press the point on the top-right of the LCD display. The square appears in the center of the LCD display. SU LEARN NG ALIGNMENT 1 While pressing the COMMANDER OFF button, press the MENU button and EXIT button. COMMANDER OFF MENU EXIT 4 Press the square in the center of the LCD display. When the calibration is complete, the beep sounds, and the LCD display returns to the selecting display of display setting. SU The setting display for calibrating the alignment of the LCD display appears. SU LEARN NG ALIGNMENT LEARN NG DISPLAY DISP-OFF ALIGN CONTRAST Unit Settings 2 Press the point on the bottom-left of the LCD display. The other point appears on the topright of the LCD display. SU Note When calibrating, be sure to press the point accurately, otherwise the calibration will be off and you will need to start over. 5 Press and hold the LEARN NG ALIGNMENT COMMANDER OFF button for more than 2 seconds. COMMANDER OFF The Remote Commander turns off. If you want to quit before finishing Press and hold the COMMANDER OFF button for more than 2 seconds. The Remote Commander turns off. Continued 39 Setting the LCD display (continued) 3 Press and hold the COMMANDER OFF button for more than 2 seconds. COMMANDER OFF Setting the contrast of the LCD display You can adjust the contrast of the LCD display if the screen is not viewed properly. To change this setting, perform the following procedure. The Remote Commander turns off. 1 While pressing the COMMANDER OFF button, press the OK button. COMMANDER OFF If you want to quit before finishing Press and hold the COMMANDER OFF button for more than 2 seconds. The previous status returns, and the Remote Commander turns off. OK The setting display for contrast appears. SU LEARN NG CONTRAST A/B POWER 1 4 7 +10 2 5 8 0 3 6 9 ENTER TOP MENU REC DISPLAY MAIN/SUB INPUT LIST 2 Press the CHANNEL +/­ button to adjust the contrast of the LCD display. CHANNEL You can set the contrast level from 1 to 15. CHANNEL +: Darker contrast CHANNEL ­: Lighter contrast Note If you press the CHANNEL +/­ button and the contrast level is already at the minimum/maximum level, the beep does not sound. The level can be set from 1 to 15. 40 Setting the beep The Remote Commander is preset at the factory with the confirmation beep set to on. To change this setting, perform the following procedure. 3 Press "BEEP" on the Label keys. BEEP 1 While pressing the COMMANDER OFF button, press the MUTING button. COMMANDER OFF The setting display for beep appears. The current setting is shown inside the [ ], while the other flashes. SU LEARN NG OTHER MUTING "SET" appears as the Display title. SU BEEP [ ON ] OFF LEARN NG SET 4 Press the ON or OFF key to select the beep. LIGHT DISPLAY OTHER If "OTHER" does not flash on the Label keys, press the Display title (SET) repeatedly until it appears. ON: Turns on the beep. The beep setting changes and a beep sounds each time you press the key. 5 Press and hold the COMMANDER OFF button for more than 2 seconds. COMMANDER OFF Unit Settings 2 Press "OTHER" on the Label keys. OTHER The Remote Commander turns off. "OTHER" appears as the Display title. SU LEARN NG OTHER If you want to quit before finishing Press and hold the COMMANDER OFF button for more than 2 seconds. The previous status returns, and the Remote Commander turns off. BEEP DS_TIME CLOCK RESET If you want to return to the previous display Press the BACK button or the COMMANDER OFF button. 41 Adjusting the clock You can adjust the clock after setting. To change this setting, perform the following procedure. 3 Press "CLOCK" on the Label keys. CLOCK 1 While pressing the COMMANDER OFF button, press the MUTING button. COMMANDER OFF The setting display for clock appears. SU LEARN AM NG CLOCK MUTING "SET" appears as the Display title. SU SET STD_TIME LEARN NG SET 4 Press the F/f/g/G buttons to change the time or day. LIGHT DISPLAY OTHER If "OTHER" does not flash on the Label keys, press the Display title (SET) repeatedly until it appears. 2 Press "OTHER" on the Label keys. Each time the G or g button is pressed, the Clock display changes in order (the day y the hour y the minute y the day). Each time the F or f button is pressed, the hour or minute changes by 1 hour or minute. Select the hour or minute by pressing the (G/g) button first. OTHER 5 Press "SET" on the Label keys. SET "OTHER" appears as the Display title. SU LEARN NG OTHER With a beep sound, the clock is started. [. . . ] To play at double speed To select the recording time by 30 minutes and begin recording *1 To avoid accidental recording, the REC key does not work unless pressed for more than 2 seconds (factory setting). *2 The Z key does not work unless pressed for more than 2 seconds (factory setting). PLAY x2 Q. TIMER 80 DVR (Digital Video Recorder) ­ DVR, PVR, DVR/Satellite Combo, DVR/Cable Combo KEY DISPLAY POWER FUNCTION To turn the power on/off KEY DISPLAY EPG*1 MENU EXIT TOOLS VOLUME + VOLUME ­ CHANNEL + CHANNEL ­ MUTING FUNCTION To use the program guide To call up the MENU To exit the MENU To go into the OPTION setting mode Volume up (TV) Volume down (YV) Channel up Channel down To mute the volume on the TV. To select the channel previously selected To replay, or to go into REC/ REVIEW mode during play (After about 5-second rewind, replay begins. ) To bring up Master Guide To switch the antenna output Page down Page up To select the desired recorded program (It is necessary to have recorded the desired program. ) To select the desired recorded program (It is necessary to have recorded the desired program. ) Category guide To return to the home display from any display To display a drop menu and toggle to change the user 1 ­ 9, 0, ENTER To change the channel (To change to channel 5, for example, press 0 and 5, or press 5 and ENTER. ) · INFO m N M S. INDEX REC*2 x X DISPLAY . FAVORITE > INPUT To enter the subchannel number To display program information To rewind To play To fast-forward To bring up the Station Index To record To stop To pause To turn on the display To select the previous track To use the "FAVORITE" function To select the next track To switch the output of the SAT receiver to the TV (When connecting a TV cable or antenna to the receiver, the output switches between a TV and SAT program) To briefly replay the scene To call up the title of the recorded program To briefly fast-forward the scene To move the cursor upward To move the cursor downward To move the cursor to the right To move the cursor to the left To enter the selection of the MENU display RECALL REPLAY*1 LIVE_TV*1 ANT/SW ­ PAGE*1 PAGE +*1 ­ THUMBS*1 THUMBS +*1 Appendix T· LIST*1 ·t F f g G OK CATEGORY HOME VIEWER *1 This key corresponds to Tivo service or the replay service. [. . . ]