User manual SONY RM-LP204M

[. . . ] 8 Using the lists ] ] } Tip Under normal conditions, the batteries should last for about 3 months. When the remote no longer operates the receiver, replace all the batteries with new ones. Notes · Do not leave the remote in an extremely hot or humid place. · Do not use a new battery with old ones. · Do not mix the alkaline batteries and other kinds of batteries. [. . . ] Adjusts the lens shift of the picture. If you have programmed the remote to control nonSony components, note the following: ­ All the items may not appear when you select a component. ­ All the items displayed may not function. Tip Location of parts and basic remote operations Do the following procedure to perform set up menu operations on the DVD player. 1 Select the DVD player from the function list. 2 Press the i button repeatedly to display the SUB menu. To display Do this TOP MENU DVD MENU SET UP Press TOP MENU button. Select "SET UP" in the SUB menu. 3 Use the control button to perform menu operations on the DVD player. Make sure that "DVD" is selected in the CURSOR TYPE list. To exit the menu operation, press RETURN O/ EXIT. To display the DVD menu, use the AV MENU button (page 7). a) "SIDE A/B" appears for non-Sony LD players. b) Only with Sony TVs that supports the wide-picture mode. c) Only with Sony TVs with the picture-in-picture function. d) Only with the Sony CD changer. 11GB Using the lists Chart of lists See the tree diagram below for the list hierarchy. <MACRO1> p 1-NO SET 2-NO SET 3-NO SET 8 Repeat steps 4 through 7 to program up to 16 IR codes. When you have finished programming IR codes, select "Exit" in step 7. 16GB To delay the output of an IR code 1 In step 4, move the easy scroll key to select "Common", then press the key to enter selection. 2 Move the easy scroll key to select "WAIT TIME", then press the key to enter selection. 3 Move the easy scroll key to select the time to delay the output of an IR code, then press the key to enter selection. You can specify from 1 to 10 second delay (in 1 second increments). To erase a programmed IR code 1 In step 4, move the easy scroll key to select "Common", then press the key to enter selection. 2 Move the easy scroll key to select "NO SET", then press the key to enter selection. To turn off all Sony components (SYSTEM STANDBY) 1 In step 4, move the easy scroll key to select "Common", then press the key to enter selection. 2 Move the easy scroll key to select "ALL OFF", then press the key to enter selection. However, this function cannot be applied to some Sony components. To cancel programming Starting macro play 1 Press FUNCTION. The function list appears. Using the lists USER1 USER2 p MACRO1 MACRO2 2 Move the easy scroll key to select "MACRO1" or "MACRO2", then press the key to enter the selection. The IR codes appear in the display window as they are performed. Notes · Pressing any of the following buttons during a macro play operation will cancel the macro play sequence before it is complete. ­ AV ?/1 ­ ?/1 ­ SYSTEM STANDBY ­ SOUND FIELD ­ FUNCTION ­ RM SET UP · When the Macro Play function does not work properly, set "WAIT TIME" between each operation. Move the easy scroll key to select "Exit" or "Cancel" during any step, then press the key to enter the selection. Tips · In step 6, when "*" is displayed in front of the function, the function is pre-programmed. [. . . ] Sort?[VIDEO 1 ] = *CH+ *CH*INPUT SELECT 20GB 3 Move the easy scroll key to select "On" or "Off", then press the key to enter the selection. Adjusting the contrast of the display You can adjust the contrast of the display. When you select "On", the TV INPUT list appears. <TV INPUT> p TV-VIDEO1 TV-VIDEO2 TV-VIDEO3 1 Press RM SET UP. The set up list appears. MENU EDIT AUTO POWER BACK LIGHT p CONTRAST Using the lists 4 Move the easy scroll key to select the video input of the TV, then press the key to enter the selection. 2 Move the easy scroll key to select "CONTRAST", then press the key to enter the selection. When you want to select component video input, select TV-COMPO1 or 2. Notes · Switching to VIDEO 1­6 input may not be automatic on all Sony TVs. This is because some TVs cannot receive remote control codes immediately after being turned on. [. . . ]