User manual SONY SPP-A5000

[. . . ] Do not use the telephone to report a gas leak in the vicinity of the leak. Use only the power cord and batteries indicated in this manual. Check with local codes for possible special disposal instructions. Caution You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Privacy of communications may not be ensured when using this phone. Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] 31) Adjust the cordless handset volume. wa MIC (Microphone) qk # button (p. 56) Used to change the number of digits of the phone number in the Caller ID list. Getting Started 29US Basics Making calls 1 Pick up the cordless handset from the base unit. 2 Press (TALK) and wait until I (HEADSET) jack VOL switch (HOLD) "TALK" appears on the display and the display also shows the talk time in hours, minutes and seconds. The IN USE lamp on the base unit lights up. If you hear five short error beeps and "NO CONNECTION" appears on the display, move closer to the base unit. (*TONE) (EZ ACCESS) (ERASE) (CALL WAITING/FLASH) 3 Dial the phone number. 4 When you're done talking, press (OFF) or replace the cordless handset on the base unit. The display turns off. To make a call after checking the phone number You can dial the phone number before pressing (TALK) or (EZ ACCESS). If you make a mistake when dialing the phone number, press (ERASE) to erase the number. 30US Basics Making calls when the headset is connected When a headset (optional) is connected to the I (HEADSET) jack on the cordless handset, you can talk through the headset. Open Making calls using the EZ Access function To set up the access number, see "Setting up the EZ Access function" on page 21. 1 2 3 Basics Pick up the cordless handset from the base unit. Dial the phone number (e. g. , 1-201-123-4567, or 011-. . . ). The system dials first, the access number set up with the EZ access function, and then the phone number you dialed in step 2. "TALK" appears on the display. TALK E12011234567 NEW OLD MASSAGE RING OFF 4 When you're done talking, press (OFF) or replace the cordless handset on the base unit. Note If you have set up a phone number with the EZ access function, just press (EZ ACCESS) to dial the phone number (i. e. skip step 2). Additional tasks To Adjust the cordless handset volume Put a call on hold*1 Do this Set the VOL switch to H (high), M (middle) or L (low). Tips · Although the phone number displayed on the redial list is up to 15 digit, the redialing will be successful. · If you redial the same number repeatedly, this number will only be counted as one number of the total five registered numbers that can be redialed. · When dialing from a phone number with a registered name, that name will be displayed in the list in step 2. continued Basics 33US Making calls (continued) To erase the dialed phone number one by one 1 Display the name or phone number you want to erase by doing steps 1 to 3 on page 33. 2 3 Turn Jog Dial to choose "ERASE REDIAL", and then press Jog Dial. Turn Jog Dial to choose "YES", and then press Jog Dial. You hear a long confirmation beep, and the number is erased. To erase the entire dialed phone numbers at once 1 Press (PGM). 2 3 4 Turn Jog Dial to choose "MEMORY MANAGE", and then press Jog Dial. Turn Jog Dial to choose "ERASE ALL RDL", and then press Jog Dial. Turn Jog Dial to choose "ERASE REDIAL", and then press Jog Dial. You hear a long confirmation beep, and the entire number are erased. To store the dialed phone number into the Phone Directory See page 39. 34US Basics Receiving calls 1 When you hear the phone ring: · Press (TALK). or I (HEADSET) jack VOL switch (HOLD) · Pick up the cordless handset from the base unit when the cordless handset is placed on the base unit. (When Quick talk is set to "ON"; see page 36) "TALK" appears on the display and the display also shows the talk time in hours, minutes and seconds. The IN USE lamp on the base unit lights up. Basics (CALL WAITING/FLASH) (PGM) 2 When you're done talking, press (OFF) or replace the cordless handset on the base unit. [. . . ] · Caller ID service may not work when the phone is connected to a Private Branch Exchange (PBX). · The call is made through company which does not offer Caller ID service. "UNKNOWN NUMBER/ NAME/CALLER" will appear on the display. · The call was "blocked. " "BLOCKED NUMBER/ NAME/CALL" will appear on the display. [. . . ]