User manual SONY STR-DH100

[. . . ] 4-129-741-13(1) FM Stereo FM/AM Receiver Operating Instructions STR-DH100 ©2009 Sony Corporation WARNING To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. To reduce the risk of fire, do not cover the ventilation opening of the apparatus with newspapers, tablecloths, curtains, etc. Do not place the naked flame sources such as lighted candles on the apparatus. To reduce the risk of fire or electric shock, do not expose this apparatus to dripping or splashing, and do not place objects filled with liquids, such as vases, on the apparatus. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. [. . . ] · Be sure to connect the video output of the video component to the TV, so that the image is displayed on the TV. However, you cannot do video recording via this receiver. Refer to the operating instructions of each connected component for details. AM loop antenna (aerial) (supplied) DMPORT ANTENNA AM DC5V 0. 7A MAX IN OUT IN IN IN OUT IN L L L L R R R R SA-CD/CD MD/TAPE SAT BD/DVD VIDEO * The shape of the connector varies depending on the area code of this receiver. Notes · To prevent noise pickup, keep the AM loop antenna (aerial) away from the receiver and other components. · Be sure to fully extend the FM wire antenna (aerial). · After connecting the FM wire antenna (aerial), keep it as horizontal as possible. Tip To output the sound of the TV from the speakers connected to the receiver, be sure to turn off the TV's volume or activate the TV's muting function. 15GB 5: Preparing the receiver and the remote Connecting the AC power cord (mains lead) Connect the AC power cord (mains lead) to a wall outlet. Notes · Before connecting the AC power cord (mains lead), make sure that the metallic wires of the speaker cords are not touching each other between the SPEAKERS terminals. · Connect the AC power cord (mains lead) firmly. AC power cord (mains lead) Performing initial setup operations Before using the receiver for the first time, initialize the receiver by performing the following procedure. This procedure can also be used to return settings you have made to their factory defaults. Be sure to use the buttons on the receiver for this operation. ?/1 MASTER VOLUME INPUT SELECTOR SPEAKERS (OFF/A/B/A+B) FM MODE TUNING MODE TUNING MEMORY/ ENTER BASS TREBLE DISPLAY DIMMER MUTING PHONES MEMORY/ENTER 1 2 3 Press ?/1 to turn off the receiver. Hold down ?/1 for 5 seconds. "PUSH" and "ENTER" appears on the display alternately. Press MEMORY/ENTER. After "CLEARING" appears on the display for a while, "CLEARED" appears. All the settings you have changed or adjusted are reset to the initial settings. To the wall outlet 16GB Inserting batteries into the remote Insert two R6 (size-AA) batteries in the RM-AAU055 Remote Commander. Observe the correct polarity when installing batteries. 6: Selecting the speaker system You can select the speakers you want to drive, if you have connected the speakers to SPEAKERS A and B terminals. Be sure to use the buttons on the receiver for this operation. SPEAKERS (OFF/A/B/A+B) Getting Started MASTER VOLUME INPUT SELECTOR SPEAKERS (OFF/A/B/A+B) FM MODE TUNING MODE TUNING MEMORY/ ENTER BASS TREBLE DISPLAY DIMMER MUTING PHONES Notes · Do not leave the remote in an extremely hot or humid place. · Do not use a new battery with old ones. · Do not mix manganese batteries and other kinds of batteries. · Do not expose the remote sensor to direct sunlight or lighting apparatuses. · If you do not intend to use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion. · When you replace the batteries, the remote buttons may be reset to their factory settings. If this happens, reassign the buttons again (page 28). · When the remote no longer operates the receiver, replace all the batteries with new ones. Press SPEAKERS (OFF/A/B/A+B) repeatedly to select the speaker system you want to drive. To select The speakers connected to the SPEAKERS A terminals The speakers connected to the SPEAKERS B terminals The speakers connected to both the SPEAKERS A and B terminals (parallel connection) Light up SP A SP B SP A SP B To turn off the speaker output Press SPEAKERS (OFF/A/B/A+B) repeatedly until the "SP A" and "SP B" indicators on the display do not light up. Note You cannot switch the speaker system by pressing SPEAKERS (OFF/A/B/A+B) when the headphones are connected. 17GB Playback Selected input [Display] VIDEO [VIDEO] BD/DVD [BD/DVD] SAT [SAT] MD/TAPE [MD/TAPE] Input buttons Components that can be played back VCR, etc. , connected to the VIDEO jack Blu-ray disc player, etc. , connected to the BD/ DVD jack Satellite tuner, etc. , connected to the SAT jack MD deck, tape deck, etc. , connected to MD/TAPE jack Super Audio CD, CD player, etc. , connected to the SA-CD/CD jack Enjoying sound from the component connected to the receiver TV ?/1 SLEEP TV INPUT AV ?/1 ?/1 SYSTEM STANDBY VIDEO BD/DVD SAT MD/TAPE SA-CD/CD TUNER DMPORT SA-CD/CD [SA-CD/CD] BASS TREBLE BD/DVD MENU TUNER Built-in radio tuner [FM or AM band] DMPORT [DMPORT] DIGITAL MEDIA PORT adapter connected to DMPORT jack 1 4 7 >10/ 2 5 8 0/10 3 DISC SKIP 6 9 D. TUNING - MEMORY AMP MENU ENTER TOOLS/ OPTIONS MUTING CLEAR DISPLAY AMP MENU MUTING 2 3 Turn on the component and start playback. Press MASTER VOL +/­ to adjust the volume. You can also use MASTER VOLUME on the receiver. , V/v/B/b RETURN/EXIT TV VOL MASTER VOL MASTER VOL +/­ MENU/HOME 1 Tips Press the input button to select a component. You can also use INPUT SELECTOR on the receiver. [. . . ] If you connect the receiver to an outdoor antenna (aerial), ground it against lightning. To prevent a gas explosion, do not connect the ground wire to a gas pipe. Outdoor FM antenna (aerial) Receiver ANTENNA AM Ground wire (not supplied) To ground continued 31GB Radio stations cannot be tuned in. · Check that the antennas (aerials) are connected securely. Adjust the antennas (aerials) and connect an external antenna (aerial), if necessary. [. . . ]