User manual SONY VAIO VGN-FW495J

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ­ Reorient or relocate the receiving antenna. [. . . ] 3 Press ERASE while the bookmark indicator and "ERASE " are flashing. Note 2 If you want to combine messages to which the bookmark is already added, delete the bookmark before combining messages. 33GB Playing Back the Specified Section Repeatedly -- A-B Repeat While playing back a message, you can set the start (A) and end (B) points for a section you wish to play repeatedly. x STOP Jog lever (x·B) A-B (repeat)/ PRIORITY 1 During playback, press A-B (repeat)/PRIORITY briefly. The starting point (A) of the section you wish to play repeatedly is set. "A-B B" flashes. 2 During playback, press A-B (repeat)/PRIORITY briefly. The finishing point (B) of the section is set. "A-B" and " " are displayed and the specified section is played back repeatedly. To resume normal playback Press the jog lever (x·B). To stop A-B Repeat playback Press xSTOP. Notes · You cannot set A-B Repeat for a section that overlaps two or more messages. · If you do not set the finishing point (B), the finishing point is automatically set at the end (or the beginning) of the message. 34GB BEditing Messages Adding a Recording Notes · At a factory setting, you cannot add a recording not to erase the message by accidental operation. See "Using an Adding Recording" (page 52) to change the setting. · The added or overwritten portion of a message will be recorded in the same recording mode (ST, SP or LP; see page 54) as the original message, regardless of the current recording mode setting. · You cannot add or overwrite a recording if the remaining memory is not long enough. For more information, see "Troubleshooting" (page 59). Built-in microphone Editing Messages zREC/REC PAUSE xSTOP OPR indicator Adding a Recording to a Previously Recorded Message When REC-OP in the menu is set to ADD, you can add a recording to the message being played back. To combine messages, redo the procedures. · You cannot combine messages of different recording modes. 1 2 3 4 Press xSTOP to stop the IC recorder. Press the jog lever up or down (>/. ) to display the number of the second of the two messages you want to combine. While pressing DIVIDE/ (bookmark), press ERASE for more than 1 second. "CMB" will flash for 10 seconds. Press ERASE while the display is flashing. The two messages are combined into one and the messages will be renumbered as in the illustration on this page. To cancel erasing Press xSTOP before step 4. 42GB Moving Messages to a Different Folder You can move the recorded messages to another folder. When you move a message to another folder, the one in the previous folder will be deleted. xSTOP Jog lever (FOLDER/x·B) Editing Messages Example: Moving Message 3 in Folder B to Folder C 1 Play back the message you want to move. 2 Turn the jog lever toward FOLDER repeatedly to select the folder that you want to move the message into. The destination folder and "MOVE" flash. The first and last 5 seconds of the message will be played back. 3 Press the jog lever (x·B). The message is moved to the destination folder. Messages are sorted in order of the recorded date and time or the number of the priority marks in the folder. To cancel moving the message Press xSTOP before step 3. 43GB Adding Priority Mark(s) -- Priority Mark Function Usually the recorded messages are lined up in the order of recording. By adding priority marks (#) to important messages, you can renumber the messages in the order of their priority. There are four levels, "###" (the most important), "##", "#", and no priority mark. You can add priority marks both in the stop mode and in the playback mode. xSTOP Jog lever (x·B) A-B (repeat)/PRIORITY Adding Priority Mark(s) in the Stop Mode 1 2 Select the message you want to mark. Press A-B (repeat)/PRIORITY for more than 1 second. "#" and the message number indication will flash on the display window. 3 Press A-B (repeat)/PRIORITY repeatedly to select the number of priority mark(s) (#) while indications are flashing. The setting is finished when the priority mark(s) (#) light(s) steadily in the display window and the messages are renumbered. 44GB Adding Priority Mark(s) during Playback 1 Press A-B (repeat)/PRIORITY for more than 1 second during playback of the message you want to mark. "#" and the message number indication will flash on the display window while the first and last 5 seconds of the message is played back 10 times. 2 Press A-B (repeat)/PRIORITY repeatedly to select the number of priority mark(s) (#). Editing Messages 3 Press the jog lever (x·B) to fix the setting. The setting is finished and the messages will be renumbered. e. g. When there are 3 messages in a folder Messages with priority mark(s) Messages are sorted in order of the number of priority mark(s) (#) in a folder. [. . . ] Move . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 53 35 37 43 19 11 19 14 17 17 54 15 43 D Digital Voice Editor . . . . . . . . . . . . . . . . . . . . 56 Digital Voice Up function . . . . . . . . . . . . 30 Editor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]