User manual SONY VAIO VGN-SZ680E

[. . . ] HEWLETT­PACKARD MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance or use of this material. Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett-Packard. This document contains proprietary information which is protected by copyright. [. . . ] Switches 3 through 8 are used to specify drive connectivity and functionality according to host or customer requirements. The default setting is all switches ON. Address Jumpers To set the drive's address, use the SCSI-2 address jumpers, and perform the following steps: 1. Attach the static-grounding wrist strap by following the instructions on the package. Attach one end of the strap to the system chassis. Locate the address jumpers on the rear of the DDS-3 drive. Figure 1­3 shows the rear of the DDS-3 drive with the significant bits identified. Set the drive's SCSI-2 target address to an address that's not used by another SCSI-2 device. Using Figure 1­3 as a guide, use needlenose pliers to set the jumpers. When finished, refer to "Preparing the System, " later in this chapter, for information on verifying the jumpers have been set correctly and your system sees the drive. Do not use SCSI-2 address 7 because the system's SCSI-2 controller uses address 7 by default. We advise that you do not use SCSI-2 address 6 because the root disk drive uses it. 2. 3. NOTICE: 1­8 Introduction Bit 0 Bit1 Bit 2 Term PWR SCSI Connector SCSI ID Term PWR* Bit 2 SCSI ID Power Connector Term PWR* Bit 2 Bit 1 Bit 0 Bit 1 Bit 0 0 1 2 3 (Default) 4 5 6 *Term PWR is not used in SONY workstation configurations. Figure 1­3. Rear View of DDS-3 Drive and SCSI Address/Jumper Settings 1­9 Introduction Operation Mode Switches ON 12345678 Compression Disabled, No Host Control ON 12345678 Compression Disabled, Host Can Control Compression ON 12345678 Compression Enabled, No Host Control ON 12345678 Compression Enabled, With Host Control Default Setting Figure 1­4. Adding or Removing Expansion Brackets You are now ready to begin the hardware installation of your DDS-3 drive. The step-by-step instructions for installing the drive are found in the owner's guide that came with your workstation. 1­16 Chapter 2 Using the DDS-3 Drive This chapter provides the following information on using your DDS-3 drive: · · · DDS-3 drive configuration Controls and features of the DDS-3 drive Using the DDS-3 drive To verify SONY-UX system operation, see the owner's guide that came with your workstation. For more information on checking or reconfiguring the kernel for a device driver or file, see System Administration Tasks Manual: SONY 9000 Series 700 Computers. 2­1 Using Your DDS Drive Your DDS-3 Drive Configuration Your SONY-UX operating system comes with preconfigured device files and drivers. If you use these preconfigured device files and drivers, you won't need to configure your DDS-3 drive with the operating system. To find out more about creating and using device files, see the owner's guide that came with your system. Controls and Features of the DDS-3 Drive Your DDS-3 tape drive is either a 3 1/2-inch form factor, or a 5 1/4-inch form factor DDS-3 tape drive with data compression and a SCSI interface. It conforms to the DDS-3 format standard for storing computer data. It's a high-capacity, high transfer-rate device for data storage on tape. Figure 2­1 shows the LEDs and eject button of the DDS-3 drive. Tape Light Clean/Attention Light Eject Button Figure 2­1. DDS-3 Drive Controls and Indicators 2­2 Using Your DDS Drive LEDs The front panel has two colored LEDs: the Tape Light and the Clean/Attention Light. The Tape Light flashes green to show activity (loading, unloading, reading, and writing). Steady green means a cartridge is loaded. [. . . ] If you are using SONY VUE as your interface, you can also access the Support Tools Manager through the sys_admin directory. Three interfaces are available with the Support Tools Manager: a command line interface (accessed through the cstm command), a menu-driven interface (accessed through the mstm command), and the graphical user interface (accessed through the xstm command). For more information on these user interfaces, see the online man pages by entering the following at a command line prompt: man cstm man mstm man xstm RETURN RETURN RETURN 3­5 Troubleshooting and Removal/Replacement Procedures To access the Support Tools Manager, perform the following steps: 1. Click on the Terminal Control on the Front Panel of your Workspace. Terminal Control A terminal window opens. 2. 3. Move the mouse cursor into the terminal window and click the left mouse button. [. . . ]