User manual SONY VAIO VPCB1190X

[. . . ] ______________ GB VAIO VPCB1190X © 2006 Sony Corporation Printed in China Printed on 100% recycled paper using VOC (Volatile Organic Compound)-free vegetable oil based ink. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] · If you do not use the remote for a long period of time, remove the batteries to avoid damage from battery leakage and corrosion. 3 Hold down (stop) on the unit, and press DISC 1 until "LOCK" appears. Select a folder on an "ATRAC" disc or MP3 disc 4 Unplug the power cord. To stop automatic scanning Press (stop) . Power To set the clock To tune in a station with a weak signal If "TUNED" does not appear and the scanning does not stop, press TUNING MODE repeatedly until "AUTO" and "PRESET" disappear, and then press +/­ on the remote (or TUNING +/­ on the unit) repeatedly to tune in the desired station. Connect the power cord to a wall socket. If the plug does not fit the wall socket, detach the supplied plug adaptor (only for models equipped with an adaptor). 1 Turn on the system. Press (power) . Select a track or file 2 Select the clock set mode. Press CLOCK/TIMER SET on the remote. If the current mode appears on the display, press / on the remote repeatedly to select "CLOCK SET" and then press ENTER on the remote. 3 Set the time. Wall socket Find a point in a track or file To reduce static noise on a weak FM stereo station Press FM MODE repeatedly until "MONO" appears to turn off stereo reception. Speakers Right speaker Left speaker Press / on the remote repeatedly to set the hour, and then press ENTER on the remote. Use the same procedure to set the minute. When you turn off the system after setting the clock, the clock display appears instead of the demonstration display. The clock settings are lost when you disconnect the power cord or if a power failure occurs. Select Repeat Play Select a disc Changing the display To change Press Selecting a music source Press the following buttons (or press FUNCTION repeatedly). To select Press Switch to CD function from another source Exchange other discs while playing Information on the display* Display mode (See below. ) DISPLAY repeatedly when the system is on. DISPLAY repeatedly when the system is off. * For example, you can view CD/"ATRAC"/MP3 disc information, such as the track or file number or folder name during normal play, or the total play time while the player is stopped. To change the play mode CD Tuner AM loop antenna CD on the remote. AUDIO IN . Component (connected using an audio cord) Press PLAY MODE repeatedly while the player is stopped. You can select normal play ("ALL DISCS" for all discs, "1DISC" for a disc, or " *" for all "ATRAC" files and MP3 files in the folder on the disc), shuffle play ("ALL DISCS SHUF, " "1DISC SHUF, " or " SHUF*"), or program play ("PGM"). * When playing a CD-DA disc, (SHUF) Play performs the same operation as 1DISC (SHUF) Play. The system offers the following display modes. Display mode When the system is off, 1) Demonstration Antennas Clock Power Saving Mode2) 1) Find a location and an orientation that provide good reception, and then set up the antenna. Keep the antennas away from the speaker cords and the power cord to avoid picking up noise. FM lead antenna (Extend it horizontally. ) or Brown side for other regions The clock display is replaced by lighting and flashing of the display window. The display is turned off to conserve power. Use buttons on the unit to reset the unit to its factory default settings. General The display starts flashing as soon as you plug in the power cord even though you have not turned on the system. 1 Disconnect and reconnect the power cord, and then turn on the system. 2 Press PLAY MODE/TUNING MODE , 2 Press CLOCK/TIMER SET . 3 Press / repeatedly to select "PLAY Loaded disc SET" then press ENTER . "ON" appears, and the hour indication flashes. · Press DISPLAY twice while the system is off. The demonstration disappears. DISPLAY and (power) at the same time. All user-configured settings, such as preset radio stations, timer, and the clock, are deleted. · Standby power consumption: 0. 5 W · Halogenated flame retardants are not used in the certain printed wiring boards. · Lead-free solder is used for soldering certain parts. · Halogenated flame retardants are not used in cabinets. (Except for the United States model) Notes on discs · Before playing, wipe the disc with a cleaning cloth from the center out to the edge. · Do not clean discs with solvents, such as benzine thinner, or commercially available cleaners or antistatic spray intended for vinyl LPs. · Do not expose discs to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight. 5 Press ENTER to add the track or file to the program. "­ ­. ­ ­" appears when the total time exceeds 100 minutes for a CD, or when you select a CD track whose number is 21 or over, or when you select an "ATRAC" file or MP3 file. 4 Set the time to start playing. Press / repeatedly to set the hour, and then press ENTER . [. . . ] · If the system is brought directly from a cold to a warm location or is placed in a very damp room, moisture may condense on the lens inside the CD player, and cause the system to malfunction. In this situation, remove the disc, and leave the system turned on for about a few hours until the moisture evaporates. CD/MP3 player The sound skips, or the disc will not play. · Wipe the disc clean, and replace it. · Move the system to a location away from vibration (for example, on top of a stable stand). · Move the speakers away from the system, or place them on separate stands. [. . . ]