User manual SONY VAIO VPCB11FGX/B

[. . . ] Eveready is a registered trademark of Eveready Battery Company, Inc. IBM, IBM PC AT, and IBM PS/2 are registered trademarks of IBM Corporation. MS, MS-DOS, and Microsoft are registered trademarks of Microsoft Corporation. Windows 95, Windows 98, Windows NT, and Windows for Pen Computing are trademarks of Microsoft Corporation. [. . . ] Contact your network administrator or local help desk for details on log-off parameters for your network. Resuming System Operation To resume system operation, (from either Suspend-to-RAM or Suspend-to-Disk modes), press the Suspend/Resume button. 2 · From Suspend-to-RAM mode After a few seconds, the system returns to the Fully On state and system operation resumes. Note that the display turns on shortly before the pen becomes active due to the power-up sequences observed by the system. · From Suspend-to-Disk mode Active data is read from the hard disk drive, and after 15 to 30 seconds, the system returns to the Fully On state. 2-6 Using the Stylistic 2300 Pen Tablet Note that power to several system components must be restored before system operation resumes. Allow sufficient time for system operation to resume before attempting to use the system. If your system uses Suspend-to-Disk mode, it will take longer to resume operation as compared to using Suspend-to-RAM mode. Time is needed to read data from the hard disk drive. · Use the system as you normally would once system operation resumes. All programs resume at the point where execution stopped when system operation was suspended. Using Hotpads Hotpads are pen-active areas below the system display that you can use to change the display and speaker settings while the system is running. To use a hotpad, tap directly on it with the pen. You can also press and hold the pen tip against the Volume, Contrast, and Brightness hotpads to automatically repeat the hotpad function. The location of each hotpad is shown in Figure 2-1. Programmable Speaker Mute 2 Display Select Fast Slow Slow Fast Down Up Down Volume Down Volume Up Up Brightness Contrast (certain systems do not have contrast hotpads) Figure 2-1 Hotpads A summary of each hotpad's function is given below: · Programmable hotpad This hotpad can be programmed for application-specific functions. · To select an object, tap the pen tip once on the object. · To drag an object, place the pen tip directly over the object, then press and hold the pen tip against the display screen while you move the pen. Pen Tether Attachment Point Pen Tip Thumb Grip Barrel Button Figure 2-2 Stylistic 2300 Pen Using the Pen 2-9 Charging the Battery Pack The Stylistic 2300 battery pack can be charged while it is installed in the pen tablet. Connect a DC power source, such as the AC adapter, to the DC input connector on the pen tablet. The DC Input icon appears in the Status display. If the battery pack charge level is below 90%, the battery pack begins charging and the Charging icon appears in the Status display. If the battery pack charge is 90% or higher when you connect DC power, the battery pack will not charge; this prevents overcharging the battery pack. Look at the Battery Gauge icon in the Status display to determine the percent of charge in the battery pack. See "Status Display" in Chapter 1 of this manual for a description of the Battery Gauge icon. As long as DC power remains connected to the pen tablet, the charging process continues until the battery pack charge reaches 100%. Charge times shown in Table 2-2 are for a fully discharged battery pack charging both while the pen tablet is and is not in use. Table 2-2 Battery Pack Charging Time Battery Pack Charge Level Reached 90% 100% Approximate Charge Time (tablet not in use) 3 hours 5 hours Approximate Charge Time (tablet in use) 9 to 10 hours 12 hours Also note the following with respect to charging the battery pack: · You can use the system, suspend system operation, or shut down and turn off the system without interrupting the charging process; however, using the system while the battery pack is charging will cause the battery pack to charge at a slower rate, as noted in Table 2-2. · As noted in the procedure above, the system will not begin charging the battery pack if the battery pack charge level is 90% or higher when the system is initially connected to external DC power. [. . . ] · Elevators, highways, tunnels, (automobile, subway, railroad, or pedestrian) where a person with impaired hearing might be isolated in an emergency. · Places where telephones are specifically installed to alert emergency authorities such as fire, police, or medical assistance personnel. · Hospital rooms, residential health care facilities, convalescent homes, and prisons. · Workstations for the hearing impaired. [. . . ]