User manual SONY VAIO VPC-EA22FX/B

[. . . ] Securing a T20 with a Security Bracket and Cable Lock . Securing a T30 Thin Client with a Cable Lock . B­1 B­1 B­1 B­3 C Electrostatic Discharge Preventing Electrostatic Damage . C­2 D Routine Thin Client Care and Shipping Preparation Routine Thin Client Care . [. . . ] Disconnect any external devices or cables. Å Å Ä WARNING: To reduce the risk of personal injury from electrical shock and/or hot surfaces, be sure to disconnect the power cord from the wall outlet and allow the internal system components to cool before touching. WARNING: To reduce the risk of electrical shock, fire, or damage to the equipment, do not plug telecommunications or telephone connectors into the network interface controller (NIC) receptacles. CAUTION: Static electricity can damage the electronic components of the Thin Client or optional equipment. Before beginning these procedures, ensure that you are discharged of static electricity by briefly touching a grounded metal object. See Appendix C, "Electrostatic Discharge, " for more information. Hardware Reference Guide 2­1 Hardware Upgrades 3. Access the Thin Client system board. See the section "Gaining Access to the Thin Client System Board" for more information on how to access the system board. 4. Remove, if necessary, any hardware that will be replaced. Install any optional equipment. Many of the instructions for installing Thin Client options can be found and downloaded from the Compaq website at http://www. compaq. com. 6. Replace the Thin Client's side access cover. Reconnect any external devices and power cords. Turn on the monitor, the Thin Client, and any devices you want to test. Load any necessary drivers. Many of the drivers necessary for installing optional Thin Client at hardware can be found and downloaded from the Compaq website http://www. compaq. com. 10. Reconfigure the Thin Client, if necessary. 2­2 Hardware Reference Guide Hardware Upgrades Locating the Power On Switch The location of the power on switch varies according to your Thin Client model. Remove the screw 1 as shown in the following illustration. This screw must be removed in order to pry open the PCMCIA slot cover. 2. Remove the slot cover 2 by prying it open with your fingers or a small flathead screwdriver until it pops loose. Accessing the T30 PCMCIA slot Hardware Reference Guide 2­11 A Specifications Compaq Thin Client T1010 Dimensions Height Width Depth Approximate Weight Temperature Range (fanless design) Operating Nonoperating Relative Humidity (non-condensing) Maximum Altitude (unpressurized) Operating Nonoperating Power Supply Operating Voltage Range Rated Line Frequency Power Output (maximum) Rated Input Current (maximum) Heat Dissipation On Suspend Off 8. 9 in 3. 9 in 6. 9 in 12. 5 lb 32° to 104° F 14° to 140° F 20­80% 10, 000 ft 40, 000 ft 90­264 VAC 47­63 Hz 20 W 4. 0 A 453. 3 BTU/hr 444. 3 BTU/hr 228. 9 BTU/hr 22. 6 cm 9. 9 cm 17. 5 cm 5. 5 kg 0° to 40° C -10° to 60° C 20­80% 3048 m 12192 m 90­264 VAC 47­63 Hz 20 W 4. 0 A 114. 2 kg-cal/hr 111. 9 kg-cal/hr 57. 7 kg-cal/hr Hardware Reference Guide A­1 Specifications Compaq Evo Thin Client T20 Dimensions Height Width Depth Approximate Weight Temperature Range Operating Nonoperating Relative Humidity (noncondensing) Operating Nonoperating Maximum Altitude (unpressurized) Operating Nonoperating Power Supply Operating Voltage Range Rated Line Frequency Power Output (maximum) Rated Input Current (maximum) Heat Dissipation On Suspend Off 8. 4 in 3. 6 in 7. 7 in 3. 0 lb 32° to 104° F 14° to 140° F 10­90% 10­95% 10, 000 ft 40, 000 ft 90­265 VAC 47­63 Hz 18 W 1. 5 A 350. 1 BTU/hr 345. 6 BTU/hr 228. 9 BTU/hr 21. 3 cm 9. 1 cm 19. 5 cm 1. 4 kg 0° to 40° C -10° to 60° C 10­90% 10­95% 3048 m 12192 m 90­265 VAC 47­63 Hz 18 W 1. 5 A 88. 2 kg-cal/hr 87. 1 kg-cal/hr 27. 7 kg-cal/hr A­2 Hardware Reference Guide Specifications Compaq Evo Thin Client T30 Dimensions Height Width Width (foot/base) Depth Approximate Weight Temperature Range Operating Nonoperating Relative Humidity (noncondensing) Operating Nonoperating Maximum Altitude (unpressurized) Operating Nonoperating Power Supply Operating Voltage Range Rated Voltage Range Rated Line Frequency Power Output Rated Input Current (maximum) Heat Dissipation Maximum Nominal 10. 2 in 2. 7 in 4. 6 in 8. 5 in 4. 6 lb 32° to 104° F -40° to 140° F 10­90% 10­95% 10, 000 ft 40, 000 ft 90­132 VAC 100­120 VAC 50­60 Hz 40 W 1. 5 A 136. 6 BTU/hr 53. 3 BTU/hr 26. 0 cm 7. 0 cm 11. 75 cm 21. 6 cm 2. 1 kg 0° to 40° C -40° to 60° C 10­90% 10­95% 3048 m 12192 m 180­265 VAC 200­240 VAC 50­60 Hz 40 W 1. 0 A 34. 4 kg-cal/hr 13. 4 kg-cal/hr Hardware Reference Guide A­3 B Security Provisions Securing the Thin Client The T20 and T30 Thin Clients are designed or can be set up to accept a security cable lock. See the following sections for instructions on securing your specific Thin Client. Securing a T20 Thin Client The T20 Thin Client can be secured in two ways: An optional bracket and cable lock can be added. The unit can be secured to a tabletop or counter. Securing a T20 with a Security Bracket and Cable Lock A separate security bracket option and cable lock option are available for the T20. This bracket, which attaches to the T20, combined with the cable lock, prevent the outside access panel from being removed. To order these options and to download the installation instructions for these options, visit the Compaq website at http://www. compaq. com/products/thinclients/options/index. html. Hardware Reference Guide B­1 Security Provisions Securing a T20 to a Tabletop or Counter The T20 Thin Client can be secured to a tabletop or workspace counter to prevent the unit from being moved. To secure the Thin Client: procedure base screws from This Thin Clientrequires you to remove thewith longer screws. the T20 and replace two of them Before beginning the procedure, locate two screws of the same thread as the screws you are replacing. These new screws should be long enough to go through the tabletop or counter, though the base, and back into the Thin Client. Remove the base of the Thin Client by unscrewing the four screws at the bottom that secure the base to the unit. Use the base of the Thin Client as a guide for pre-drilling two holes on the tabletop or counter as shown in the following illustration. Pre-drilling the screw holes B­2 Hardware Reference Guide Security Provisions 3. Attach the base back to the Thin Client using only the two screws that will not be used in securing the unit to the table. [. . . ] For information about the recommended temperature and humidity ranges for your Thin Client, see Appendix A, "Specifications, " in this guide. Keep liquids away from the Thin Client and keyboard. Turn off the Thin Client before you do either of the following: Wipe the exterior of the Thin Client with a soft, damp cloth as needed. Using cleaning products may discolor or damage the finish. [. . . ]