User manual SONY VPCEG24FX/L

[. . . ] Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths. • Condensation can occur in the device due to rapid, drastic changes in ambient temperature-when the device is moved from one location to another, or air conditioning is turned on or off, for example. Using the device while condensation is present can cause damage. If there is reason to believe that condensation might have occurred, leave the device for several hours until the condensation has completely dried out. [. . . ] • ABOUT THE PROTECTION CIRCUIT This speaker system has an internal protection circuit that shuts off the speaker unit when an excessive input signal is applied. If the speaker unit emits no sound, reduce the volume level of the amplifier immediately. The sound will return automatically in several seconds. • Place the speaker on a flat and smooth surface. Sensitivity (1W, 1m) *2 Maximum SPL (Calculated, 1m) *3 Frequency range (-10 dB) *2 Subwoofer filter Satellite filter Satellite impedance Connector Location • Do not place the device in an unstable position where it might accidentally fall over. • Do not place the device in a location where it may come into contact with corrosive gases or salt air. • Construction work should be carried out in accordance with constructionrelated law and always by a professional constructor. If the device installation requires construction work, make sure to observe the following precautions. - Choose mounting hardware and an installation location that can support the weight of the device. - Avoid locations that are exposed to constant vibration. - Use the required tools to install the device. • When transporting or moving the device, always use two or more people. 1 Pass the safety wire through the eyebolt on the rear of the speaker. Eyebolt 2 INSTALL THE SPEAKER Installing on the wall (using the included brackets) 1 Place the bracket base on the wall and mark the position for screws/bolts. The diameter of seven holes for screw/bolt (not included) is ø6. 5 mm. 2 Make holes in the wall for the bolts, as required, and feed the bolts through the holes. The narrow edge of the bracket base should be oriented downward. 4 Attach the mounting bracket to the speaker with the included screws with captive washer. The narrow edge of the mounting bracket should be oriented downward. Bracket base WARNING • Do not use the included brackets for ceiling installation. • Do not use the UB-DXR8 for wall installation. Pre-installation (Preparation of the cable) Use stranded wire for cables attached to the Euroblock connector. Strip their insulation as shown in the figure and connect them. About 7 mm (0. 3 in. ) Installing on the ceiling (using the optional UB-DXR8) To determine the appropriate size of the UB-DXR8, download the “U BRACKET OWNER’S MANUAL” from the following manual library site. http://www. yamaha. co. jp/manual/ 1 Assemble two L-shaped brackets into a U-shape using the M5 × 10 screws included with the UB-DXR8 as shown below. Peel off the sheet from each rubber spacer (14 mm thickness; included with the speaker), and attach the spacers to the inside of each bracket arm aligning the holes so that the hexagon bolts can be inserted. M5 × 10 NOTE Do not plate stranded wires by solder. [. . . ] A signal input to CH1 of INPUT is output from ST1 of SATELLITE SPEAKERS, and signal input to CH2 of INPUT is output from ST2 of SATELLITE SPEAKERS. For VXS10ST/VXS10STW, connect the included 5-pin Euroblock connector as shown below and set the appropriate wattage when using 100 V/70 V line. 100V/× 70V/200W 100V/200W 70V/100W 100V/100W 70V/50W 100V/50W 70V/25W Rubber spacer Mounting bracket Captive washer screw Rubber spacer 2 Make sure that the width of the U bracket matches the speaker width. 3 Affix the U bracket on the ceiling using appropriate mounting hardware. [. . . ]