User manual SONY XAV-602BT

[. . . ] Install the unit with the monitor facing straight ˎˎ forward; do not install it at a slanted angle. Notes on the power supply lead (yellow) When connecting this unit in combination with other ˎˎ stereo components, the amperage rating of the car circuit to which the unit is connected must be higher than the sum of each component's fuse amperage rating. If ˎˎ no car circuits are rated high enough, connect the unit directly to the battery. Gray Gray/black striped Right *11 Green Green/black striped Left *2 Purple Purple/black striped Right Smartphone Parts list The bracket  is attached to the unit before ˎˎ shipping. Before mounting the unit, use the release keys  to remove the bracket  from the unit. [. . . ] A ˎˎ power antenna (aerial) without a relay box cannot be used with this unit. Memory hold connection When the yellow power supply lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off. Notes on speaker connection Before connecting the speakers, turn the unit off. ˎˎ Use speakers with an impedance of 4 to 8 ohms, and with ˎˎ adequate power handling capacities to avoid damage. Do ˎˎ not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers with those of the left speakers. Do ˎˎ not connect the ground (earth) lead of this unit to the negative (–) terminal of a speaker. Do ˎˎ not attempt to connect the speakers in parallel. Connecting active speakers (with ˎˎ built-in amplifiers) to the speaker terminals may damage the unit. To ˎˎ avoid a malfunction, do not use the built-in speaker leads installed in your car if they feature a common negative (–) lead for the right and left speakers. Do ˎˎ not connect the unit’s speaker leads to each other. Notes on connection If ˎˎ [Check Audio Output Wiring] appears in the display, make sure the speaker and amplifier are connected correctly. To ˎˎ use the monitor for the rear seats, connect the parking brake switch cord to the ground (earth). *2 *1 For details on installing the microphone, see “Installing the microphone ()” on the reverse side (Except for XAV-742). *2 RCA pin cord (not supplied) *3 HDMI connection cable or MHL connection cable (supplied) (XAV-712BT/612BT only) *4 The sound is output from this terminal only when ZONE × ZONE is activated. This terminal outputs a fixed level regardless of the volume control of the unit. *5 A separate adaptor may be required. *6 The USB rear cable labeled “HIGH CHARGE” is recommended to use for recharging the battery of a connected device. *7 To connect a smartphone to the main unit, an appropriate cable (not supplied) is required. *8 GPS module for AV Center (XA-NV300T) (not supplied). *9 The USB rear cable without “HIGH CHARGE” label (XAV-742/712BT only) T *10 he HDMI in/MHL in port (XAV-712BT/612BT only) *11 Speaker impedance: 4 – 8 ohms × 4 XAV-712BT/612BT only   or *1 Smartphone Securing the connection of the HDMI/MHL connection cable (XAV-712BT/612BT only) Secure the connection between the HDMI/MHL connection cable and main unit, using the hook and loop fastener . 1 Wrap the hook and loop fastener  around the neck of a cable. 2 Pull the hook and loop fastener  firmly back around the neck of the other cable.  3 Bring the ends of the hook and loop fastener  together to secure the connection of the cables. *1 HDMI connection cable or MHL connection cable (supplied) (XAV-712BT/612BT only) English Precautions Choose the installation location carefully so that the ˎˎ unit will not interfere with normal driving operations. [. . . ] ˎˎ Clip (not supplied) b Clips (not supplied) XAV-612BT/602BT only A B  How to detach and attach the front panel (XAV-612BT/602BT only) Before installing the unit, detach the front panel. -A To detach Before detaching the front panel, press and hold OFF for more than 2 seconds to turn off the unit. Press , and then hold the left side of the front panel and pull it open to the right. Tip If you also lift the left side of the front panel slightly , the front panel comes out easily.  Face the hook inwards. XAV-742/712BT  XAV-612BT/602BT  -B To attach Place the recesses  of the front panel onto the pegs  on the unit, then lightly push the left side in. Removing the bracket Before installing the unit, remove the bracket  from the unit. Keep the release keys  for future use as they are also necessary if you remove the unit from your car. Caution Handle the bracket  carefully to avoid injuring your fingers. Catch Catch    1 Insert the release keys  into the catches between the unit and the bracket  at the same time until they click. [. . . ]