User manual SOUNDCRAFT EFX 12

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual SOUNDCRAFT EFX 12. We hope that this SOUNDCRAFT EFX 12 user guide will be useful to you.

Lastmanuals help download the user guide SOUNDCRAFT EFX 12.


Mode d'emploi SOUNDCRAFT EFX 12
Download
Manual abstract: user guide SOUNDCRAFT EFX 12

Detailed instructions for use are in the User's Guide.

[. . . ] TM TM User Guide 1 IMPORTANT Please read this manual carefully before using your mixer for the first time. © Harman International Industries Ltd. 2007 All rights reserved Parts of the design of this product may be protected by worldwide patents. ZM0356-02 Soundcraft is a trading division of Harman International Industries Ltd. Information in this manual is subject to change without notice and does not represent a commitment on the part of the vendor. [. . . ] Featuring the deep, rich reverb algorithms that Lexicon® are renowned for the effects processor offers increased versatility and high quality effects, all instantly accessible via the extremely intuitive front panel controls. The effects processor has 32 programs which are held in two banks of 16 programs which can be stored to allow you to create your own custom effect settings. Front panel controls include a Program Select knob, Tempo and Store buttons, and three independent Parameter knobs that provide instant access and control over the most critical parameters for the selected effect. The table on page 30 lists the functions of the parameter knobs for each fx program. Note: When the console is powered up the program recalled will always be the selected program in BANK A. FX OPERATION Select and Load a Program Turn the Program Select knob to choose a program. Note that the console has 32 programs which are held in two banks of 16 programs. There are individual BANK A and BANK B LED's to indicate which bank is currently active. When turning the rotary Program Select knob through 360 degrees (a full rotation) the selected bank will alternate between BANK A and BANK B. Set the gain on the input channel appropriate to the source (vocal microphone, guitar, keyboard, etc. ). Set the FX send on the input channel to the 12 o'clock position. Set the EFFECTS Fader on the FX section to the fully down position. Provide source signal (by speaking or singing into the microphone, playing guitar, keyboard, etc. ) on the selected channel. Turn up the FX Send level on the channel until the Red CLIP LED in the FX Panel lights only occasionally. If the red Input LED stays lit, too much signal is being sent to the effect processor: reduce FX Send on the input channel. Raise the EFFECTS Fader towards the 0dB position to feed the required level of FX Processor output signal to the mix. To increase or decrease the amount of effect on the signal, adjust the FX Send level on the channel that you want affected. 22 FX PROCESSOR CONTROLS 1. Tempo Button - Tapping this button twice sets the Delay Time of the selected program. The LED flashes to indicate current tempo. Can be tapped in time with music source to synchronise the delay. Store Button - Stores program modifications to one of the program locations. Press and hold for three seconds will store the preset in the current location. The LED will flash rapidly during the store operation and then stay illuminated for 1 second to show the operation is complete. [. . . ] Normally connections are made with positive to positive, negative to negative. If this is reversed, the result will be out-of-phase signals (see `phase' above). Post-fade The point in the signal path after a fader and therefore affected by the fader position. Pre-fade The point in the signal path before a fader, and therefore unaffected by the fader position. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SOUNDCRAFT EFX 12

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual SOUNDCRAFT EFX 12 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag