User manual SOUNDTECH PS3402 POWER SOURCE

[. . . ] PS3402 Power SourceTM Stereo Power Amplifier Operation Manual COPYRIGHT © 2001 SOUNDTECH UNAUTHORIZED REPRODUCTION IS A VIOLATION OF APPLICABLE COPYRIGHT LAWS PS3402 Power SourceTM 2 Channel Digital Power Amplifier Table Of Contents 1 2 3 4 5 6 7 8 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Warranty Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Panel Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Note: The ¼" input accepts either tip/ring/sleeve or tip/sleeve phone connectors. Bridge Mode Switch Bridges the outputs as indicated. Run this in either bridged mono or in stereo depending on the position of the switch. Clip Limiter When an audio signal drives an amp's output circuit beyond its power capability, its clips, flattening the peaks of the waveform. A clip limiter detects this and quickly reduces the gain to minimize the amount of overdrive. The PS3402 has a clip limiter built in and you can switch it on or off as shown at the rear panel. Input Filter (Low Cut Filter) The switchable low-frequency (LF) filter rolls off signals below either 30Hz or 50Hz. This improves performance by eliminating subsonic cone motions making more power available for the speaker rated frequency range. The filters frequency setting for both channels is controlled by the 30Hz/50Hz slide switch. This heavy duty power cord uses a 20 amp connector where one blade is perpendicular instead of parallel to the other blade. This is a safety feature to prevent you from plugging into a circuit less than 20 amps. The outlet receptacle will have one T shaped blade insert that will accept both types of connectors. If you do not have this type of receptacle, please contact your local electrician for an upgrade. Do not obstruct air flow to this opening. 6 V Connecting Your System A. MOUNTING The PS3402 Power SourceTM is designed for standard 19" rack mounting. In addition, the amplifier is provided with sturdy no-skid rubber feet for secure table top or stacked operation. When rack mounting one or more amplifiers or when mounting in combination with other equipment, be sure to allow adequate front and rear ventilation to avoid possible heat related damage to your PS3402 Power SourceTM or other rack mounted items. B. OPERATING PRECAUTIONS Your SoundTech PS3402 Power SourceTM power amplifier is well protected from any external faults. However, we recommend following these common sense precautions: 1. Safety Instructions Read and follow all of the safety warnings in this manual. . Do not expose the PS3402Power SourceTM to water or other liquids. Always unplug the unit if water is present. [. . . ] The tip is positive, the ring negative and the sleeve is ground. This input will also accept an unbalanced tip/sleeve connector. G. POWER REQUIREMENTS Your SoundTech PS3402 Power SourceTM is pre-wired at the factory for the correct line voltage (120V or 220-240V) and is furnished with the appropriate power cord and fuse. If fuse replacement is necessary, always use a fuse with the exact type and rating as specified on the specifications page of this manual or as indicated on the unit itself. H. [. . . ]