User manual SPA-QUIP SP-1200

[. . . ] Spa Water Treatment Recommended Chemical Values Chlorine. . . . . . . . . . . . . . . . . . . . . . . . . 1. 5 - 3. 0 PPM ( Parts Per Million ) pH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7. 4 - 7. 6 Total alkalinity . . . . . . . . . . . . . . . . 100 - 120 PPM It is important to maintain your spa water chemistry to the above values to ensure a healthy experience both for you as bathers and for your spa pool equipment. [. . . ] 9. SET TEMP USER TIMER CLOCK USER ALARM SLEEP TIMES MAINT TIMERS MISC OPTIONS ADV. DEFAULTS Pump 2 Two pushes of the on/off button cycles the pump as follows: Push 1 (Pump On) Push 1 (Pump Hi) The Hi/Low speed button can be used to change the pump speed: ADV OPTIONS () (ESC) Push 2 (Pump Low) Push 2 (Pump Off) 1. TIME* *N/A circulation pump installations O. 50 1. HEAT CONTROL () (SET) ( ) LCD displays "PUMP OFF", button LEDs off. The Hi/Low speed button has no effect in this mode. Scroll to SET Notes: 1) If left on, these pumps will automatically switch off after 25 minutes. 2) If the heater element is on, running either pump in high speed mode may cause the heater to load shed and switch off. If this occurs the heater will come back on approximately 5 seconds after high speed is deselected (pump running in low speed or pump off). Page 26 Page 7 3. 4 Pump 1A & 1B (Single speed pumps, no 24hr circulation pump fitted) Three pushes of the Pump 1A button cycles the pump as follows: 7. 8. 2 Main Display The SP1200 touch pad LCD consists of two lines of text and four numerical digits. The display typically shows three quantities - pool temperature, set temperature and the clock (weekday and time). By default the pool temperature is displayed on the numerical digits leaving the clock and set temperature on the two lines of text. If preferred, the user may change the layout so either the set temperature or clock are shown on the main display (four numerical digits) rather than on the smaller text lines. In addition a cycling mode can be selected whereby each of the three possible views is presented for 10 seconds each. Available options: Push 1 (Pump On) Push 2 (Pump Off) Push 3 (Pump Auto) LCD displays "PUMP ON", button LEDs green. LCD displays "PUMP OFF", button LEDs off. LCD displays "PUMP AUTO", button LEDs green. Notes: 1) If Pump 1A is left in"PUMP ON or "PUMP OFF" modes, this pump will automatically revert to "Auto" mode after 90 minutes. 2) If the heater element is on, running the pump may cause the heater to load shed and switch off. If this occurs the Two pushes of the Pump 1B button cycles the pump as follows: 1. POOL TEMP (default setting, set temp and clock on text lines) 2. SET TEMP (clock and pool temp on text lines) 3. CLOCK (set temp and pool temp on text lines) 4. CYCLING (cycles through the above views 1 ­ 3 for 10 seconds each) 7. 8. 3 Changing The Main Display 1) 2) 3) 4) 5) Select the MISC OPTIONS submenu from the main menu. Select the MAIN DISPLAY menu item Press the SCROLL button to begin main display selection. Use the UP and DOWN buttons to set the desired view. [. . . ] 5) Press the SCROLL button to save the new settings and return to the user alarms submenu. 36. 75 Mon, O C Usr timer 29:59 12:00PM USER TIMER counting down 7. 5. 2 Disabling A User Alarm If you want to disable a user alarm follow the procedure outlined above until you reach step 4. At this point use the UP and DOWN buttons to adjust the weekday setting until no days are selected (see display below). 7. 4 Clock The SP1200 contains a real time clock that will retain the correct time even during short power cuts. The clock provides the user with a convenient way to tell the time in the pool and is also used to time sleep periods, filtration timing and the user timers. The clock can be configured to operate in either 12 or 24 hour mode. [. . . ]