User manual SPEKTRUM DX6I

[. . . ] Leaders in Spread Spectrum Technology 6-Channel 10-Model Memory Full Range DSM2TM 2. 4GHz Radio System for Airplanes and Helicopters TAblE Of CONTENTS Spektrum's DX6i 6-channel DSM2 Full Range Airplane and Helicopter System . . . . . . . . . . . . . . . . . . . . . . . . 6 DSM2 DuaLink Technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 ModelMatch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Receiver Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The sensitivity around center can be tailored using the Exponential function to precisely adjust control feel. Dual and Expo rates can be controlled by their respective dual rate switches (aileron, elevator and rudder) or by one common switch (Aileron D/R, Elevator D/R, Rudder D/R or the Gear switch). See COMBI SWITCH screen on page 46 for detail on combining the Dual rate switches. Dual rate values are adjustable from 0­100%. The factory default settings for both the 0 and 1 switch positions are 100%. Exponential values are adjustable from -100% to +100% with a factory default of 0% or inhibit. Either switch position may be selected as the low or high rate by placing the switch in the desired position and adjusting the value accordingly. Note: A negative (-) Expo value will increase sensitivity around neutral, and a positive (+) Expo value will decrease sensitivity around neutral. Normally a positive value is used to desensitize control response around neutral. TO ADjUST ThE DUAl AND EXPO RATES With the transmitter already powered on and the main screen displayed, press and release the ROLLER to enter the ADJUST LIST. Rotate the ROLLER to the right until D/R&EXPO is highlighted on screen. Reduce photo to 13. 5% ADJUST LIST MODEL SELECT D/R&EXPO TRAVEL ADJ Press the roller to access the Dual Rate and Expo function. Main 2 Reduce photo to 13. 5% D/R&EXPO AILE 1 100% ELEV 1 100% RUDD 1 100% List INH% INH% INH% Reduce photo to 13. 5% ADJUST LIST MODEL SELECT Main Move the respective D/R switch in the desired position (0 or 1) that you wish to change. Rotate the roller to highlight the desired channel's EXPO or D/R value that you wish to adjust. Press the roller to access the D/R or EXPO value. Rotate the roller to adjust the D/R or Expo value. After the desired value is programmed press the roller to deselect the value. TO RETURN TO ThE MAIN SCREEN Press and hold the roller for more than 3 seconds then release the roller and the system will return to the main screen. TO RETURN TO ThE ADjUST lIST SCREEN Rotate the roller to highlight LIST then press the roller. The Dual Rate and Expo functions for aileron, elevator and rudder can be combined on a single switch conveniently allowing high or low rates to be selected via one switch. The choices for this are found on the COMBI SWITCH on page 46. 62 SPEKTRUM DX6i · RADIO PROGRAMMING GUIDE SPEKTRUM DX6i · RADIO PROGRAMMING GUIDE 63 TRAvEl ADjUST The Travel Adjust function allows the precise end-point adjustments of all six channels in each direction independently. The travel adjust range is from 0­125%. Channels available for programming are: · THRO: · AILE: · ELEV: · RUDD: · GEAR: · FLAP: Throttle Aileron Elevator Rudder Retractable Landing Gear Flap Press the roller to access the TRAVEL ADJ function. Reduce photo to 13. 5% TRAVEL ADJ List THRO+100% AILE+100% ELEV+100% RUDD+100% GEAR+100% FLAP+100% Move the respective stick or switch in the desired direction that you wish to change the travel adjust. Rotate the roller to highlight the desired channel's value that you wish to adjust. Press the roller to access the travel adjust value. [. . . ] This will enable Horizon to better answer your questions and service you in the event that you may need any assistance. For questions or assistance, please direct your email to productsupport@horizonhobby. com, or call 877. 504. 0233 toll free to speak to a service technician. INSPECTION OR REPAIRS If this Product needs to be inspected or repaired, please call for a Return Merchandise Authorization (RMA). Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. [. . . ]