User manual SPYKER 64

[. . . ] Install 1 drive pin (18) into axle for drive wheel. 7. 8. Model 34 tire shown Now install hopper to frame. Slide the spinner shaft (12) through the bearing hole in the bottom of the hopper. Install the wheels. Be sure slotted hub side is next to the frame. [. . . ] The spread thins or feathers at the outer edges, eliminating sharp, "Edge of spread" lines which cause stripes and streaks. Extra coverage can be given under trees and other heavy feeding areas without showing "edge of spread" lines. Gaps and double overlaps are less likely. Small errors in travel are forgiven and do not show. WARNING: When spreading products containing herbicides, exercise extreme caution with respect to careless spreading and to wind-drift. CONTACT OF SOME PRODUCTS ON SOME PLANTS CAN BE FATAL. If a dial setting is not found, use the size and weight comparison table found on the back page. Determine a dial setting on the low side. If the setting proves to be too low, cover the area more than one time. A higher setting can be used when a proven dial setting is established. REMEMBER - Published dial settings can be approximate only. The operation of the spreader, the condition of the material (damp or dry or over-pulverized) and weather conditions, are all contributing factors. For these reasons, it's often a good idea to spread the area 2 times - at one-half rate in cross directions (SEE INFORMATION ON ONE-HALF RATE DIAL SETTINGS ON REFERENCE CHART ON THE BACK PAGE. SPREADING AT ONE-HALF RATE DIAL SETTINGS IS HIGHLY RECOMMENDED UNDER DAMP & HUMID CONDITIONS. BECOME FAMILIAR WITH THE OPERATION OF THE SPREADER BEFORE YOU PUT MATERIAL IN THE HOPPER. Practice walking with the spreader, opening and closing the rate gate at the appropriate times. Travel at a constant speed and operate the spreader lever position. Remember: Open the rate gate after the spreader is in motion at operating speed (about 3 mph. , or at a brisk walking pace). Close the rate gate while spreader is still at operational speed. Model 54 Only 43 44 45 05-46-0500 05-94-0065 05-94-0064 1 1 3 Plastic Hopper Cover, Clear Plastic with Black Washer, Plastic Model 34 Only 46 47 48 49 50 51 Optional 52 53 54 55 05-82-0000 05-99-0021 SL-EH-1005 05-94-0065 Extension Hopper Cover - Model 64 & 34 Screen Cover - Model 54 SS-97-0006 SL-HP-1044 99-50-1081 05-97-0008 SS-95-0004 05-24-1070 1 2 1 1 1 Axle 18 3/4" Long Drilled Axle, Gears, Gear Box, Spinner Assembly Axle, Cotter Pin Spinner Shaft 3/8 x 6 1/2 Pneumatic 8. 5 x 3. 5 Hand Hold Rotary Agitator Use the rotary agitator only if needed. Free-flowing, lump-free materials will not require the agitator. The rotary agitator is easily installed or removed. Note the clockwise rotation & sweep. [. . . ] (Newton's law of motion: To every action there is always an opposed and equal reaction. ) Serviceability - 24 hour replacement parts service available direct from the factory. Series 22 spreaders shipped set up except hand hold/bump bar and push handle or tractor pull bar. Manufacturer and Product Bent Grass or Red Top Bag Weight 0. 5# 1# 2# 0. 5# 1# 2# 2# 3# 4# 2# 4# 6# 2# 4# 6# 4 oz. Coverage 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1, 000 1. 25 2. 0 2. 5 2. 5 3. 0 3. 5 2. 75 3. 0 3. 25 6. 0 7. 0 7. 0 6. 0 7. 0 7. 75 1. 9 2. 1 2. 5 4. 5 4. 75 5. 0 Park, Merion, Delta, or Kentucky Bluegrass Hulled Bermuda Mixtures including coarse seeds Rye Grasses or Tall Fescue Dichondra Pensacola Bahia 1 YEAR LIMITED WARRANTY This is warranted to the original purchaser only, other than used commercially, against defects in materials and workmanship, for a period of one year from the date of purchase. *For Spyker Spreaders LLC, products employing metal gear systems, pinion and bevel, these metal gears, only, not inclusive of any other parts or materials, are warranted for the life of the spreader, not to be used for replacement or repair past original purchase. [. . . ]