User manual STANTON C.303

[. . . ] __________________________________________________________ __________________________________________________________ C. 3O3 PROFESSIONAL TABLETOP CD PLAYER INTRODUCTION Congratulations and thank you for purchasing the latest addition to the growing Stanton family. Sporting a new attitude, and a fresh, modern look, the C. 303 is a tabletop CD player with features and innovations giving club and mobile DJs a powerful, yet simple tool to mix, create, and perform their best. Designed for DJs who want to play CDs with an interface similar to vinyl, our workhorse CD player features a large jog wheel, making it possible to cue tracks easily--while an easy to read LCD display, adjustable pitch range, key lock, pitch bend, and reliable, anti-shock playback with auto cue and instant playback offer even more control and flexibility. The C. 303 even goes a step further by adding onboard sampling with four trigger buttons and cue memory, seamless looping, and a S/PDIF digital output, expanding your creative possibilities beyond that of traditional turntables. [. . . ] PITCH ­ Indicates when the pitch percentage is displayed. TIME BAR ­ Shows a proportionate visual representation of the time remaining or time elapsed. TIME DISPLAY ­ Displays the time of track(s) currently selected in increments of Minutes, Seconds, and Frames. 39. 42. ELAPSED / TOTAL / REMAIN ­ Indicates whether the time shown on the display refers to total remaining time or track remaining time. If either of these are not illuminated, this indicates elapsed track time. RELOOP ­ Indicates when there is a previously set loop, and that the loop is ready to be played again. LOOP ­ Indicates when the CD is in loop mode. SINGLE ­ Controlled by the SGL/CTN button, this indicates when the unit is set to play just one track at a time. When this is not illuminated, the CD will play continuously through all tracks. SET-UP A) CHECKING THE CONTENTS ­ Check that the carton contains all of the following items. · Tabletop CD player unit · User's manual · One pair RCA cable · One power cable · One fader start / relay cable INSTALLING THE UNIT · Place the unit on a flat, level surface. · Be sure the player is in a well-ventilated area where it will not be exposed to direct sunlight, high temperatures, or high humidity. · Try to place the unit as far as possible from Tvs and tuners, as the unit may cause undesirable interference. · The player will work normally when the unit is within 15 degrees of the vertical plane. If the unit is tilted excessively, discs may not load or unload properly, or playback may be adversely affected. · The unit's LCD screen is designed to be clearly visible within the angles shown in the figure below. Place the unit so that the LCD screen is within this visual range for optimal clarity. CONNECTIONS · Make sure that the unit and any other equipment in the signal chain are turned off prior to making any connections. · Connect the RCA cable to the rear of the unit and to the input on your mixer. · Connect the power cable to the rear of the unit and to a proper AC outlet. CAUTION · Be sure to use the supplied cables. Using other types of cables may result in unit damage. · To avoid severe damage to the unit, be sure the power is OFF when making any connections. B) C) D) OPERATING INSTRUCTIONS 1. [. . . ] ACCESSORIES (1) Connected RCA cable Operating Instruction (2) (3) Auto-start cable (4) AC Cord 1 set for L and R channel 1 pc 1 pc 1 pc NOTE: *1 with 20Khz low pass filter 6. SEARCHING TIME (TEST DISC: TCD-792) ITEM Short access time Long access time TYPICAL 2sec 4sec *2 with 20Khz low pass filter, "IHF-A" weighted (1) (2) LIMIT 4sec 6sec CONDITION Play next track Track 1-> Track 20 Track 20 -> Track 1 7. PLAYABILITY ITEM Interruption Black dot Finger prints Eccentricity Vertical deviation TYPICAL 1mm 1mm 75um 140um 1mm LIMIT 0. 7mm 0. 6mm 65um 140um 0. 5mm CONDITION TCD-725 TCD-725 TCD-725 TCD-712 W/O TRACK JUMP TCD-731R 8. PICK-UP System Object lens drive system Tracking detection Optical source Wave length 9. GENERAL System Disc loading Display Pitch control range Pitch bend Pitch accuracy 10. ENVIRONMENTAL Operating Temperature Humidity Storage Temperature Object lens drive system optical pick-up 2 dimensional paralleled drive 3 spot beam detection Semiconductor laser 780nm Compact Disc Digital Audio Front loading LCD Within +/-8%, +/-16%, +/-25%, +/-100% +/-100% 0. 1% CONDITION 5 to 35 deg. [. . . ]