User manual STANTON DJLAB.2

[. . . ] Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time. [. . . ] Make sure all faders are at "zero" and all devices are off. Next, connect your microphone and monitor headphones. Finally, connect the stereo outputs to the power amplifier(s) and/or audio receivers such as tape decks. Now you are ready to switch everything on. IMPORTANT: Always switch on your audio input sources such as turntables or CD players first, then your mixer, and finally any amplifiers. When turning off, always reverse this operation by turning off amplifiers, then your mixer, and then input devices. SPECIFICATIONS M. 201 INPUT / OUTPUT IMPEDANCE & SENSITIVITY: LINE -14dB/10K OHM ±2dB PHONO -50dB /47K OHM ±2dB MIC -60dB /2. 2K OHM ±2dB MASTER 1K OHM PHONES 0dB/33 OHM ±2dB (LOAD=32 OHM) MAX. OUTPUT (THD=1%) MASTER MORE THAN +14dBV MAX PHONES MORE THAN +21dBV MAX CHANNEL BALANCE WITHIN 3dB FREQUENCY RESPONSE: LINE 20-20KHz ±2dB PHONO 20-20KHz +2, -3dB (RIAA) MIC 20-20KHz +2/-3dB OUTPUT NOISE (IEC-A WEIGHTED) LINE LESS THAN -90dBV PHONO LESS THAN -80dBV MIC LESS THAN -50dBV THD + N: LINE PHONO MIC PHONES (MASTER 0dBV OUTPUT, MAXIMUM GAIN, w/ 20kHz LPF) LESS THAN 0. 05% 20 - 20KHz LESS THAN 0. 1% 20 - 20KHz (IEC-A WTD) LESS THAN 0. 2% 20 - 20KHz (IEC-A WTD) LESS THAN 0. 1% 20 - 20KHz (FROM LINE INPUT) LESS THAN -80dB AT 1KHz BETWEEN CHANNELS. (TERMINATED UNUSED INPUTS) CROSSTALK MIC EQ HI LOW ±10 +/- 2dB AT 10KHz ±10 +/- 2dB AT 100Hz CHANNEL EQ HI 9 +/- 2dB AT 13KHz -15 +/- 3dB AT 13KHz MID 9 +/- 2dB AT 1KHz LESS THAN -23dB AT 1KHz LOW 9 +/- 2dB AT 70Hz -26 +/- 3dB AT 70Hz POWER SOURCE AC 9V, 1000mA DIMENSIONS 230 (W) X 267 (D) X 111 (H) mm WEIGHT 1. 61Kgs BEFORE USE *Check that the following parts are included in the package with the main unit: 1) Turntable platter 2) Slip mat 3) 45-rpm adaptor 4) Counterweight 5) 500B cartridge and headshell 6) Operating instructions 7) RCA cables with ground wire 8) Target light 9) AC cord 10) Cloth dust cover *Notes: 1) Do not connect the AC power plug before assembly has been completed. 2) Read this manual carefully before using the unit and be sure to store the manual in a safe place for future reference. T. 60 TURNTABLE CONTENTS T. 60 TURNTABLE CONTENTS 1) 2) 3) 4) 5) 6) 7) 8) 9) Start/Stop Button Strobe Dots Slip Mat Center Spindle Power Switch 33/45 Button Target Light Base Pitch Control Slider Headshell Locking Nut 10) 11) 12) 13) 14) 15) 16) 17) Tonearm Arm Rest Counterweight 45-rpm Adaptor Position For Preparing Cartridge Phono Output GND Power Cord Connector PLACEMENT · Do not place the unit in a location where it will be exposed to direct sunlight or near a heating appliance. · Do not place the unit in a location where there is high humidity or a lot of dust. · Cartridge may pick up slight sound pressures or vibrations from the speakers coming along the floor or through the air resulting in feedback. Find a location which is very stable and vibration free. · The legs have functions for adjusting the height of the unit itself. Adjust the legs to stabilize the main body horizontally. ASSEMBLY 1. Remove the main unit with the packing from the box and take off the packing. Insert the turntable platter onto the center spindle. Installation of cartridge: When installing a cartridge, refer to the operating instructions of that cartridge. During installation, attach the stylus protector to guard the stylus tip from damage. (1) Connect the lead wires to the cartridge terminals. The terminals of most cartridges are color coded. Connect each lead wire to the terminal of the same color. White (L+) Left channel+ Blue (L-) Left channelRed (R+) Right channel+ Green (R-) Right channel(2) Install the cartridge to the headshell and tighten it with screws provided with the cartridge. [. . . ] In no event will Stanton be liable for any special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Stanton or otherwise. To the extent permitted by law and except as otherwise provided above, Stanton disclaims any express or implied warranties of merchantability or fitness for a particular purpose. The above warranty provides you with specific legal rights. You may also have additional rights, which are subject to variation from state to state and country to country. [. . . ]