User manual STANTON RM-50

[. . . ] Properly connect amplifier, or outboard gear to mixer. Properly set crossfader, channel faders, gain controls, and input selector toggles. Adjust headphone level and cue mix to the proper level and channel settings. Loose cartridge/headshell connection. Shorted cable. PLEASE READ CAREFULLY BEFORE USE OF THIS PRODUCT FAILURE TO FOLLOW THE INSTRUCTIONS PRINTED BELOW MAY VOID WARRANTY Program volume can't be adjusted with master volume control. [. . . ] Mic selector: Turns the mic on or off and activates the automatic talkover circuit. When activated, the automatic talkover circuit reduces the music output based on the setting of the talkover attenuation control (19). Mic EQ: Individual controls for low frequency and high frequency equalization with (+10/-10 dB) for mics 1, 2, and 3. Note: Any changes made to EQ settings will change the overall output level. Microphone 1 and 2 inputs: Combo connector is for mic 1, and the 1/4" connector is for mic 2. Input Level meter: Displays the input level. The input level is determined by the input channel controls (24). Input selector switches: Selects phono or line input. 1. Power switch: Selects power "ON" or "OFF" 3. Mono/stereo switch: switches the of Master output between a stereo and mono signal 4. Master balance control: Controls left/right signal balance of the master output. Headphone level control: Controls the overall headphone output level. It is recommended headphones with an impedance rating of 200 ohms or less be used for maximum volume. Headphone output: Connection for 1/4 inch headphone. Recommended headphone impedance is 32-200 ohms for maximum volume. Booth level control: Controls the signal level of the booth output. Cue pan: Fades the headphone output between the channel(s) selected by the cue assign switches (17) and the master one output, effectively allowing the user to preview a mix. Master level control: Controls the overall signal output level of the master output. Equalizer: Individual controls for low frequency, midrange, and high frequency equalization with (+10/-10 dB) Note: Any changes made to EQ settings will change the overall output level. Crossfader source selectors: When set to A, the select channel will be assigned to the left side of the crossfader. when set to B, the selected channel will be assigned to the right side of the crossfader. When set to BYPASS, the crossfader will be bypassed altoghter. [. . . ] To remove the line faders, remove all 4 screws. Spray a small amount of cleaner or lubricant into both ends of the fader and slide the fader back and forth a few times to spread the fluid evenly throughout the fader. Shake and wipe off excess fluid before re-assembling the fader. TE C H N I C A L S P E C I FI C AT I O N S Line inputs: Phono inputs: DJ mic input: Master output: Booth output: Record output: Headphone output: Frequency Response: Tone Control : Mic Tone: Gain Control: S/N Ratio: T. H. D: Dimension(LxWxD): 8 (RCA), 150 mV / 27K ohm 4 (RCA), 3 mV / 47K ohm 3 (XLR, 1/4"), 2. 45 mV / 3K ohm 1 (RCA), 1. 2 V / 1K ohm 1 (RCA), 1. 2 V / 1K ohm 1 (RCA), 245 mV / 10K ohm 1 (1/4"), 32 - 200 ohms recommended 20 Hz - 20 kHz, +/- 2 dB + 9/-60 dB (Hi, Mid, Low) Hi/Lo +/-10 dB 0-20dB Less than 70dB less than 0. 2% 5. 25" x 19" x 7" (134 x 482 x 178 mm) 3U FA D E R R E P L AC E M E N T To replace the cross or channel faders, follow step 1 of the cleaning instructions. Replacement parts are available from Stanton or your local Stanton dealer. CF-RM19 LF-RM19 RF-RM19 PS-RM19US PS-RM19EU PS-RM19UK Crossfader Line input fader Line input rotary (dial) fader US Power Supply (110v) European Power Supply (220v) UK only Power Supply (240v) WA R R A N T Y This unit has been designed and manufactured using quality components. [. . . ]