User manual STANTON SA.3

[. . . ] · When in use, place your mixer away from sources of hum or noise, such as transformers, or electric motors. · To prevent overheating, always provide your mixer with adequate ventilation air space. · Avoid stepping on your mixer's AC cord. Repeated compression of the cord may lead to electrical shorting. [. . . ] U s e the master mute in situations where you need to mute and unmute the mixer without having to re-adjust your Master Level (10) control. Reverse Indicator - Bi-color (red & green) LED indicates w h e n f a d e r 's d i r e c t i o n h a s b e e n r e v e r s e d ( g r e e n = n o r m a l , r e d = reversed). Reverse Button - Reverses the direction of the fade on the c o r r e s p o n d i n g f a d e r. Line fader Curve Control - Selects taper of upfader curve between a fast cut, medium curve, and long fade. I n p u t S e l e c t - To g g l e s w i t c h s e l e c t s t h e i n p u t s o u r c e between the phono and line inputs located on the back of your m i x e r. MIXER FUNCTIONS 17. Power Indicator - Blue LED indicates when power has been switched on. Line Fader - The linefader controls the level of each channel to the master outputs. Level Meter - LED meter indicates level of each channel. Use the Input Gain (4) to adjust the signal to 0dB (yellow LED). The red LED on the meter indicates when the sign a l i s c l o s e t o c l i p p i n g a n d d i s t o r t i n g t h e o u t p u t o f t h e m i x e r. Headphone Mute - Mutes the headphone output. This feature is very useful for quick cueing during mixing and scratching. Headphone Mute Indicator - Indicates when Headphone Mute (20) has been engaged. Crossfader Reverse Indicator - Indicates when crossfader reverse has been engaged. Crossfader - The crossfader fades between channel 1 and channel 2. The taper (curve) of the crossfader is determined by the crossfader curve control (23). The direction of the curve is determined by the crossfader reverse control (24). F R O N T PA N E L F R O N T PA N E L 24. Crossfader Reverse - The crossfader reverse changes the direction of the fade on the crossfader (23). F R O N T PA N E L 25. Crossfader Curve - Controls the taper (fade) shape of the crossfader (23). The crossfader curve control continually adjusts the curve from a sharp cut to a long fade. Headphone Outputs - 1/4" and 1/8" connector jacks for headphones. B A C K PA N E L B A C K PA N E L Power - Power switch to turn the mixer "ON" or "OFF". AC IN: This is the input connection for the included power s u p p l y. [. . . ] The crossfader select switch is located i n s i d e t h e m i x e r, o n t h e l e f t s i d e o f t h e fader slot. In order to use the CFSA. 3, FF1 and Penny & Giles faders, make sure the s w i t c h i s p r e s s e d D O W N . To u s e t h e C F F 2 , make sure the switch is in the UP position. T E C H N I C A L S P E C I F I C AT I O N S Line inputs: Phono inputs: Master output: Headphone output: Frequency Response: Tone Control : 2 (RCA) x 2 channels, -10 dBV /10 kOhm 2 (RCA) x 2 channels, -50 dBV / 47 kOhm 2 (TRS Balanced/RCA unbalanced), +4 dBu balanced / -10 dBV unbalanced 1 (1/4 inch), 1 (1/8 inch), greater than 32 Ohm load 20 Hz - 20 kHz, +/- 1. 5 dB Hi +9/-18 dB Mid +9/-25 dB Low +9/-25 dB S/N Ratio: Noise: T. H. D Dimension(LxWxD): Weight: Better than 94 dB (ref: max input level) -80 dBV (Line input to any output) Less than 0. 04% (1 kHz) 12. 4" x 9. 25" x 4. 33"in; (315 x 235 x 110mm) 6. 6 lbs 3 kgs R E P L A C E M E N T PA R T S The following user replaceable parts are available from your local Stanton dealer. CFSA3 LFSA3 CF-PG110 CF-F1 CF-F2 PLSA3 3PLSA3 PPSA3 PS-18US PS-18EU PS-18UK Crossfader Linefader Penny & Giles crossfader Focus Fader V1 Focus Fader V2 Phono / Line switch Phono / Line switch (w/Flash) PROTEKTTM panel US Power Supply (110v) European Power Supply (220v) UK only Power Supply (240v) WA R R A N T Y Stanton Magnetics, Inc. ­ Warranty Provision ­ Returns for Repairs or Replacement Warranty Through Stanton's authorized dealers around the World, Stanton, or one of Stanton's authorized distributors outside the U. S. , will, without charge, repair or replace, at the sole discretion of the entity responsible for making the repair or providing the replacement, any Stanton merchandise proved defective in material or workmanship for a period of one (1) following the date of original purchase. [. . . ]