Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual STANTON SA12. We hope that this STANTON SA12 user guide will be useful to you.
Lastmanuals help download the user guide STANTON SA12.
Detailed instructions for use are in the User's Guide.
[. . . ] ROTATING AND REPLACING THE OS2
ROTATING INSTRUCTIONS 1 . Remove the 2 outer screws from the round OS2 plate (removing the 2 inner screws will detach the fader from the plate) 3. Rotate the plate to the desired posi tion and tighten the screws back into the top and bottom holes. Remove the 2 outer screws from the round plate (removing the 2 inner screws will detach the fader from the plate) 3. [. . . ] · OS2 (Patent Pending) Optical Scratch switches with lock feature · Removable effects module (Patent Pending). SA-12 includes MOD1: Pitch Shifter, Flanger, and Delay; with Parameter and Mix controls. · Effects fully assignable · Foot pedal output to control effects. · 3 position cue select (Patent Pending) Pre CF Cue / Post CF Cue / Master. · 2 line, 2 phono, and 1 mic/line (switchable) inputs. · 3 band EQ with complete kill, Gain, and Pan control per channel. · Program Faders reverse switches & curve adjustments. · Cue Pan Fader · Dual headphone inputs (1/4 and 1/8 mini-jack). · Quiet-Start feature to avoid pops / noise when mixer is powered on.
DESCRIPTION OF FUNCTIONS
FADER CLEANING AND REPLACEMENT
After constant scratch use the SA-12 faders may need to be cleaned and lubri cated from time to time. This will ensure long life and keep a smooth feeling throughout the fader's lifetime. Follow the instructions below to lubricate and clean your faders: Removing a fader: 1. Make sure mixer is powered off and power supply is disconnected from back of mixer. To remove the lower faceplate, take off the 3 fader knobs and then remove the 4 screws located on the sides of the mixer (2 on each side). Lift up on the faceplate and it will slide off. Remove the fader to be cleaned or replaced by unscrewing the 2 outer screws on the fader plate (removing the 2 inner screws will detach the fader from the fader plate). Disconnect the fader from mixer by removing the 4pin connector on the bottom of the fader. Once original fader has been removed, simply plug the 4-pin connector into the new fader. NOTE: The SA-12 comes with 2 connectors, one for P+G faders and one for Focus Faders. Make sure you plug in the correct fader with the correct connector. Set selector switch to position of fader you are using (P+G or Focus Fader). Place fader back in mixer and replace 2 outer screws to secure fader. Remove 2 mounting scews from faderplate. [. . . ] Mix: Controls the dry/wet signal(dry = original signal, wet = processed signal). In the center position, the signal includes an exact 50/50 combination of both signals. Turning the knob to "wet" will have only the processed signal,
PostScript Picture BASE_callouts. eps
FRONT & BACK PANELS
without the original signal. It can be used to record even while the master volume is off. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE STANTON SA12
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual STANTON SA12 will begin.
