User manual STANTON SMX.501

[. . . ] · When in use, place your mixer away from sources of hum or noise, such as transformers, or electric motors. · To prevent overheating, always provide your mixer with adequate ventilation air space. · Avoid stepping on your mixer's AC cord. Repeated compression of the cord may lead to electrical shorting. [. . . ] CFX (Cue FX) Routes the signal from the effects to the headphones allowing the user to preview the effects mix in the headphones. MFX (Master FX) Routes the signal sent to the master output through the effects loop. This simply means that all audio coming out of the mixer will be processed. This is very useful for effects such as filters or compressors. DESCRIPTION OF FUNCTIONS MICROPHONE SECTION MIC 1 Controls the input level of Microphone input 1. MIC 2 Controls the input level of Microphone input 2. HI, MID, LOW (EQ) Individual controls for high frequency, midrange, and low frequency equalization with +9dB/Kill adjustments. Note: Any changes made to EQ settings will change the overall output level. FX This is an ON/OFF switch for the effects loop. The level is controlled by the Send and Return knobs. See Master Section for details. FRONT CURVE The Crossfader Curve Control adjusts the curve of the fader from a short cut to a long fade. CROSSFADER ASSIGN This is used to assign a channel to either side of the crossfader or to bypass it. A is the left side, B is the right side. CUE LEVEL Controls the volume of the headphone output. HEADPHONE MUTE This is a mute button that can be used to turn off the headphones without readjusting the volume. HEADPHONES This is the headphone output jack to connect your headphones. FA D E R C L E A N I N G A N D R E P L A C E M E N T After constant use the SMX. 501 faders may need to be cleaned and lubricated from time to time. This will ensure long life and keep a smooth feeling throughout the fader's lifetime. Follow the instructions below to lubricate and clean your faders: Removing a fader: 1. Make sure mixer is powered off and power supply is disconnected from back of mixer. To remove the Protekt Panel, take off the 4 main fader knobs and then remove the 4 screws located at the corners of the panels. Remove the fader to be cleaned or replaced by unscrewing the 2 outer screws on the fader plate (removing the 2 inner screws will detach the fader from the fader plate). Disconnect the fader from mixer by removing the 4pin connector on the bottom of the fader. Once original fader has been removed, simply plug the 4-pin connector into the new fader. [. . . ] 6. 7) Secure the remaining end block ensuring that the track wires (I) are not pinched between the end block and fader casing. Once assembled, move the slider from end to end to ensure operation is smooth. (NOTE: As noted earlier if you do not want to change positioning of fader, keep the 2 fader plate screws loose and shift the fader until it is aligned with the marks you created in step 1, then tighten fader plate screws. ) T E C H N I C A L S P E C I F I C AT I O N S Line inputs: Phono inputs: Mic inputs: Return inputs: Send output: Master output: Record output: Booth output: Headphone output: Frequency Response: Tone Control : Max Gain: S/N Ratio: T. H. D Dimension(LxWxD): Weight: 2 (RCA) x 3 channels, -10 dBV /10 kOhm 2 (RCA) x 3 channels, -50 dBV / 47 kOhm 2 (1/4") -50 dBV /100 kOhm 2 (1/4"), -10 dBV / 10 kOhm 2 (1/4"), -10 dBV 2 (XLR Balanced/RCA unbalanced), +4 dBu balanced / -10 dBV unbalanced 2 (RCA), -10 dBV / 100 Ohms 2 (RCA), -10 dBV / 100 Ohms 1 (1/4 inch), greater than 32 Ohm load 20 Hz - 20 kHz, + 0. 5/-2 dB + 9/-40 dB (Hi, Mid, Low) 14 dB Better than 100 dB (ref: max input level) Less than 0. 05% (1 kHz) 14" x 10. 25" x 4. 75"; 355 x 260 x 120 )mm 9. 25 lbs 4. 2 kgs R E P L A C E M E N T PA R T S The following user replaceable parts are available from your local Stanton dealer. LF501 CF-PG110 CF-F2 OS2 PP501 PS-RM19US PS-RM19EU PS-RM19UK Channel input fader Penny & Giles crossfader Focus Fader V2 Optical Scratch Switch (phono/line selector) PROTEKTTM panel US Power Supply (110v) European Power Supply (220v) UK only Power Supply (240v) WA R R A N T Y Stanton Magnetics, Inc. ­ Warranty Provision ­ Returns for Repairs or Replacement Warranty Through Stanton's authorized dealers around the World, Stanton, or one of Stanton's authorized distributors outside the U. S. , will, without charge, repair or replace, at the sole discretion of the entity responsible for making the repair or providing the replacement, any Stanton merchandise proved defective in material or workmanship for a period of one (1) following the date of original purchase. [. . . ]