User manual STANTON T.50

[. . . ] Wall or Ceiling Mounting ­ The product should be mounted to a wall or ceiling only as recommended by the manufacturer. Heat ­ The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat. Power Sources ­ This product should be operated only from the type of power source indicated on the rating label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. [. . . ] Safety Check ­ Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. CAUTION: To reduce the risk of electric shock, do not remove any cover. Refer servicing to qualified service personnel only. CAUTION The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the use to the presence of un-insulated "dangerous voltage" within the product' enclosure that may s be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operation and maintenance (servicing) instructions in the literature accompanying this appliance. CAUTION To prevent electric shock, do not use this polarized plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure. Y This device complies with Part 15 of the FCC Rules Operation is Subject to the following two conditions (1) This device may not Cause harmful interference, and (2) this device must accept any Interference received. Including interference that may cause Undesired operation. Y This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Y Unauthorized modification of this unit may cause it to no longer comply with FCC regulations and void your authority to use this device. Y Cet appareil numérique de la classe B respecte toutes les exigencies du Rèsur le materiel brouilleur du Canada. NAME OF PARTS 15 14 1 13 2 3 4 12 11 10 9 5 1 PO W ER 67 8 1) 2) 3) 4) 5) 6) 7) 8) Start/Stop Button Strobe Dots Slip Mat Center Spindle Power Switch 33 Button 45 Button Target Light Base 9) 10) 11) 12) 13) 14) 15) Pitch Control Slider Headshell Locking Nut Tonearm Arm Rest Counterweight 45-rpm Adaptor Position For Preparing Cartridge 16 17 18 16) Phono Output 17) GND 18) Power Cord Connector BEFORE USE *Check following parts included in the package with the main unit: 1) Turntable platter 2) Slip mat 3) 45-rpm adaptor 4) Counterweight 5) 500B cartridge and Headshell, except on model T. 50X, no cartridge included. 6) Operating instructions 7) RCA cables with ground wire 8) Target light 9) AC cord 10) Cloth dust cover *Notes: 1) Do not connect the AC power plug before assembly has been completed. 2) Read this manual carefully before using the unit and be sure to store the manual in a safe place for future reference. ASSEMBLY 1. Remove the main unit with the packing from the box and take off the packing. Insert the turntable platter onto the center spindle. Installation of cartridge: When installing a cartridge, refer to the operating instructions of that cartridge. During installation, attach the stylus protector to guard the stylus tip from damage. (1) Connect the lead wires to the cartridge terminals. The terminals of most cartridges are color coded. Connect each lead wire to the terminal of the same color. White (L+) Left channel+ Blue (L-) Left channelRed (R+) Right channel+ Green (R-) Right channel(2) Install the cartridge to the headshell and tighten it with screws provided with the cartridge. Hold the ribbon tape which is attached to the belt and loop the belt over the motor pulley. Be sure it does not twist. Ribbon tape Driving roller Drive belt 6. 8. 5. 9. Insert the headshell into the front end of the tonearm, then turn the lock nut clockwise with the headshell firmly held horizontally. Twist it lightly and it will screw onto the rear shaft of the tonearm. Adjustment of horizontal zero (0) balance and stylus pressure: (a) Remove the stylus protector, do not touch the stylus tip during the adjustment. [. . . ] In no event will Stanton be liable for any special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Stanton or otherwise. To the extent permitted by law and except as otherwise provided above, Stanton disclaims any express or implied warranties of merchantability or fitness for a particular purpose. The above warranty provides you with specific legal rights. You may also have additional rights, which are subject to variation from state to state and country to country. [. . . ]