User manual STRONG SRT 4401

[. . . ] Thank you for choosing this Strong satellite receiver. This receiver is of our latest development and it is designed to be capable of upgrading its software through the satellite and the Internet. It is highly recommended that you read this manual carefully to safely install your receiver and to achieve its optimum performance. Content 1. Usage This user manual is applicable for Strong SRT 4401 Evolution Digital Satellite Receiver and its related accessories. [. . . ] Press OK button to confirm your selections and go back to "System Configuration Menu" · TV Output Setup: You can set the TV settings to your personal preferences. Check your TV and VCR user manuals for the correct settings. You can change your TV settings by changing the following: Aspect: Press the Right button and set your aspect to "4:3" or "16:9" Screen Mode: Press the Right button and set your screen mode to "Pan Scan" or "Letterbox". RF TV Mode: Press the Right button and set your TV mode to "PAL-BG", "PAL-I", "PAL-DK" or "NTSC". UHF: Press the Right button and set the UHF channel number to the same UHF channel number of your TV set. This only has to be done if your TV set is connected with a coaxial (RF) Cable. If the UHF Channel numbers of the receiver and the TV set are not set the same, no picture will be displayed. RGB/CVBS: Press the Right button and set the TV mode to "CVBS" (Composite video) or "RGB" (preferred option if your TV set is compatible with it). Transparency: Press the Right button and select how transparent you want your OSD. Brightness: Press the Right button and select how you want theOSD to be. Contrast: Press the Right button and select how you want the contrast to be. Saturation: Press the Right button and select how saturated the screen to be. 1. 2. 1. 3. 2. 9. 27 28 · Parental Lock: This function changes the Personal Identification Number (PIN) that is used to control access to the menu and individual channels. In this function, you can lock/unlock channels and you can change your PIN code by applying the following steps: Menu: Using RIGHT / LEFT keys, you can select either "lock" or "unlock" and press OK. By selecting "lock", the receiver asks you to enter your PIN every time you want to access the menu. By selecting "unlock" it gives you the possibility to access the menu all the time without the receiver asking you for a PIN code. Current PIN: Enter `1111' New PIN: Enter a new PIN Retype PIN: Enter the same new PIN 1. 5. 1. 3 Installation Menu All settings that are related to TV, Dish, LNB and Satellites are within this menu. The installation menu contains "Antenna Setup", "Diseqc1. 2 Setup", "Manual Scan" sub-menus. To access the different sub menus, apply the following steps: It is recommended that you read the manual and installation instructions of your LNB, your DiSEqC switch, your 0/12V switch and your Positioner before you start setting up your receiver. Antenna Setup Menu: To set up your antenna, please apply the following steps: 1. Using UP/DOWN keys, select "Installation" and press OK. Using UP/DOWN keys, select "Antenna Setup" and press OK. [. . . ] RF-Modulator RF-Connector Frequency Output Channel TV Standard Audio Output Preset Channel 7. Power Supply Input Voltage Type Power Consumption Stand-by Power Protection 8. Physical Specification Size(W × H × D ) Weight RGB, CVBS, L, R Output with Volume Control CVBS, L, R Output(Yellow, White, Red Jack) with Volume Control RS-232, Bit Rate : 115200baud, Connector : 9-Pin D-Sub Male type 75 IEC169-2, Male/Female 470MHz to 860MHz CH21-69 for the Demodulator PAL G/I/K Selectable by Menu Setting Mono with Volume Control CH 36, Software changeable by Menu Setting AC 90~240V, 50Hz~60Hz PWM Regulator Max. 30W <=6. 5W Separate Internal Fuse 280 × 55 × 235mm, Excluding the foot. [. . . ]