User manual STRONG SRT 5003

[. . . ] Digital Terrestrial Receiver SRT 5003 User manual Bedienungsanleitung Manuel d’Utilisateur Manuale Utente Manual del usuario Návod k obsluze Upute za korištenje Picture similar PART 1 • English Table of Contents 1. 0 Instruction 1. 1 Safety Instructions 1. 2 Storage 1. 3 Equipment Set-up 1. 4 Accessories: 2. 0 Connection 2. 1 Connecting to TV and Terrestrial Antenna 2. 2 Connecting to a Digital Audio Amplifier 3. 0 Your Receiver 3. 1 Front Panel 3. 2 Rear Panel 3. 3 Remote Control 3. 4 Default PIN- code: 0000 4. 0 First Time Installation 5. 0 Main Menu 5. 1 Channel 5. 2 Installation 5. 3 Setup 5. 4 Tools 5. 5 Media+ 6. 0 OPERATION 6. 1 Changing Channels 6. 2 Accessing the Electronic Program Guide (EPG) 6. 3 Accessing the favourite channels 7. 0 Trouble Shooting 8. 0 Specifications 2 2 3 3 4 4 4 4 4 4 4 4 5 5 5 5 7 8 10 11 11 11 12 12 12 13 English Subject to alterations. In consequence of continuous research and development technical specifications, design and appearance of products may change. All product names are trademarks or registered trademarks of their respective owners. from Austrian wired line * €0, 14/Min. [. . . ] To Skip:  Skip channel or all channels press button [3], with tu select Yes in the confirmation window and press OK to save. Use the qp buttons to select Group Rename and press OK to enter. 1.  ith the qp buttons select a group and press OK. W 2.  t the appearing Keyboard use the qptu buttons to highlight desired letters or A numbers and press OK to insert. After you entered desired group name, highlight OK at the keyboard to confirm 3.  ress EXIT button to cancel the group rename. P 5. 2 Installation 5. 2. 1 Auto Scan 1.  se the qp buttons to select Installation, press OK button to enter menu. U 2.  ith the qp buttons select Auto Scan, press OK to enter the menu. W 3.  ress the tu buttons to change Scan mode, and use the qp to highlight Search, P press OK to start auto scan. 5. 2. 2 Channel Scan 1. 2. 3. 4. U  se the qp buttons to select Installation, press OK to enter the menu. W  ith the qp buttons to select Channel Scan and press OK to enter the menu. U  se the tu buttons to select one of two Scan Modes – By Channel and By Frequency. W  hen By Channel is selected use the cursor buttons to select Scan Band and Channel No. . When By Frequency is selected use the cursor buttons to select Frequency and Bandwidth. Select Network Search to ON or OFF, highlight Search and press OK to 7 English PART 1 • English start scan. After Channels are found, they will be stored and receiver switches to the first one saved in the list. 5. 2. 3 Antenna Setting 1. 2. 3. 4. P  ress MENU to enter main menu. U  se the qp buttons to select Installation, press OK to enter the menu. W  ith the qp buttons select Antenna setting and press OK to enter. P  ress the tu buttons to change setting. If On is selected, the receiver will provide 5V antenna power (for active antennas). P 5. 2. 4 LCN Mode If LCN (Logical Channel Numbering) is activated and LCN signal is provided by operator, then channels will be stored at operator defined order. You can activate/deactivate the LCN function by setting the "LCN Mode" to ON/OFF. 5. 3 Setup This menu allows you to set OSD Language, Subtitles preference, TV System, Region and Time, Timer Setting, OSD Setting and Parental Lock. 1.  ress pq buttons to highlight desired menu and press OK button to enter the P setting menus. Then press pq buttons to select desired item. [. . . ] P 5. 5. 2 Safely Remove Storage Device In "Media+" menu, select "Safely Remove Storage Device" and press OK button to safely remove the USB device. Then a message is displayed. 6. 0 OPERATION 6. 1 Changing Channels There are 4 ways of channel selection - stepping through the channel list, selection by number, from the on-screen channel list, and using the electronic programme guide (EPG). Stepping through the channel list To move through the channel list, press the pq buttons on the remote control. 11 English PART 1 • English Selected by number Enter the channel number directly by pressing numeric buttons, and press the OK button to select desired channel. [. . . ]