User manual SUB-ZERO 249RP-PS

[. . . ] Planning Information Undercounter Model 249RP All Refrigerator Serial and model number plate Interchangeable door hinge Removable wire shelves Stationary door shelves Four-sided magnetic gasket Model 249RP One piece interior Adjustable temperature control Front venting with removable kickplate Door closer from the full-size units Sub-Zero offers in its Built-In and Integrated lines of refrigeration, we round out our product line-up with a line of traditional Undercounter refrigeration which meets all of the exacting standards you have grown to expect from Sub-Zero. This all refrigerator model is ideal when coupled with an automatic ice maker next to it for the complete bar environment. [. . . ] All Undercounter models are equipped with a power supply cord with a 3-prong grounding plug which must be plugged into a mating 3-prong grounding type wall receptacle. Locate electrical within the shaded area shown in the illustration on page 3. You must follow all National Electrical Code regulations. In addition, be aware of local codes and ordinances when installing your service. Refer to the Undercounter Installation Instructions packed with the appliance, which provides step-by-step procedures for making sure the unit is installed properly. Dimensions in parentheses are in millimeters unless otherwise specified. 4 Planning Information Undercounter Model 249RP F R A M E D PA N E L S Framed door panels must be 1/4" (6) thick around the perimeter. If the panel is thicker than 1/4" (6), an edge must be routed around the panel to ensure a proper fit. Refer to the illustrations on this page. PANELS 1/4" (6) THICK OR LESS IMPORTANT NOTE: The weight of the panel cannot exceed 20 lbs (9 kg). Trim reveal 1/4" (6) min F R A M E D PA N E L D I M E N S I O N S WIDTH 1/4" (6) HEIGHT Panel Door Panel Handle Recess Location (A) 23 5/8" (600) 30 " (762) 15" (381) 20 lbs (9 kg) Framed door panel 1/4" (6) thick or less Maximum Panel Weight PANELS THICKER THAN 1/4" (6) Trim reveal 1/4" (6) min Rout to 1/4" (6) thickness Framed door panel thicker than 1/4" (6) 4" A H W Framed Door Panel Dimensions in parentheses are in millimeters unless otherwise specified. 5 Planning Information Undercounter Model 249RP O V E R L AY PA N E L OVERLAY PANEL Rear View 1/8" (3) 5/16" (8) The overlay door panel design allows for a decorative panel to cover the door trim for a more seamless appearance. To achieve this look, the most common way is to work with three panels ­ the decorative 3/4" (19) thick overlay panel, a 0. 10" (3) thick spacer panel and a 1/4" (6) thick backer panel. An accessory kit (OVERPAN) is required in order to accommodate the proper installation of the overlay panel. Additional specifications will be provided with the accessory kit. IMPORTANT NOTE: An area must be notched out on the back edge of the overlay panel at both the top and bottom hinges to avoid interference as shown in illustration on this page. [. . . ] Refer to the overlay panel specifications below. 1" Notch Required for Hinge Clearance (top and bottom) (25) Notch required for hinge clearance H IMPORTANT NOTE: The weight of the panel assembly cannot exceed 20 lbs (9 kg). IMPORTANT NOTE: The total thickness of all panels for an overlay model must be at least 5/8" (16) thick. W Overlay Door Panel O V E R L AY PA N E L D I M E N S I O N S WIDTH HEIGHT Door Panel Door Spacer Door Backer 24" (610) 23" (584) 23 5/8" (600) 30 5/16" (770) 29 3/8" (746) 30" (762) 20 lbs (9 kg) Maximum Weight (panel assembly) Dimensions in parentheses are in millimeters unless otherwise specified. 6 Planning Information Undercounter Model 249RP O V E R L AY PA N E L 145° DOOR OPENING (TOP VIEW) 24" (610) CABINETRY OPENING *MODEL 249 OVERLAY MUST EXTEND A MINIMUM OF 1-13/16" (46) BEYOND SURFACE OF ADJOINING CABINETRY AND MUST BE 1" (25) FROM ADJACENT CABINETRY TO ALLOW THE MAXIMUM DOOR SWING DOOR CLOSED 1"* (25) 3/4" (19) 113/16" (46) DOOR PANEL DOOR PANEL DOOR OPEN @ 145° 145°* Dimensions in parentheses are in millimeters unless otherwise specified. 7 [. . . ]