User manual SUB-ZERO 632-PS

[. . . ] Dimensions in parentheses are in millimeters unless otherwise specified. 2 Planning Information Built-In Model 632 S P E C I F I C AT I O N S Model 632 Overall Width Overall Height Overall Depth MODEL OPTIONS Side-by-Side Refrigerator / Freezer 48" (1219) 84" (2134) 24" (610) 18. 9 cu ft (535 L) 9. 8 cu ft (278 L) 83" (2108) 29 1/4" (743) 115 V AC, 60 Hz, 15 amp circuit 1/4" Framed Design Overlay Design Classic Stainless Steel Platinum Stainless Steel Carbon Stainless Steel 632/F 632/O 632/S 632/P 632/B Refrigerator Capacity Freezer Capacity Minimum Height (levelers in) Door Swing Clearance Electrical Requirements Plumbing Requirements Water Supply Annual Energy Usage (based on 9. 06 cents per kilowatt hour) Shipping Weight You must allow 90 days from order to delivery for platinum and carbon finishes. copper line 20­100 psi 675 kWh / $ 62 ACCESSORIES Louvered, panel or stainless steel grilles in 1" (25) increments from 10" (254) to 15" (381) high Front and grille panels for framed design in white, almond and classic stainless steel Side panels in white, almond and classic stainless steel Extended framed handles Stainless steel and polished chrome handles for overlay design Gallon door shelf Dozen egg container with lid 90° and 105° door stop kits Accessories are available through your Sub-Zero dealer. To obtain local dealer information, visit the Locator section of our website, subzero. com. Framed ­ 582 lbs (264 kg) Overlay ­ 582 lbs (264 kg) Stainless Steel ­ 630 lbs (286 kg) Specifications are subject to change without notice. Dimensions in parentheses are in millimeters unless otherwise specified. 3 Planning Information Built-In Model 632 I N S TA L L AT I O N S P E C I F I C AT I O N S 24" (610) ROUGH OPENING DEPTH EXTEND WATER LINE APPROX. 36" (914) FROM BACK WALL SHUT-OFF VALVE TOP VIEW 7" (178) E 6" (152) LOCATE ELECTRICAL WITHIN SHADED AREA 471/2" (1207) ROUGH OPENING WIDTH 833/4" (2127) ROUGH OPENING HEIGHT WITH STANDARD 11" (279) GRILLE 751/2" (1918) LOCATE WATER SUPPLY WITHIN SHADED AREA 3" (76) 18" (457) 6" (152) W FRONT VIEW DIMENSIONS Finished Rough Opening Width Finished Rough Opening Height Finished Rough Opening Depth Location of Electrical Location of Water Supply 47 1/2" (1207) 83 3/4" (2127) 24" (610) Within upper shaded area Within lower shaded area See Installation Instructions shipped with unit for detailed specifications. [. . . ] All Built-In models are equipped with a 6' (1. 8 m) power supply cord with a 3-prong grounding plug which must be plugged into a mating 3-prong grounding type wall receptacle. Locate electrical within the shaded area shown in the installation illustration. You must follow all National Electrical Code regulations. In addition, be aware of local codes and ordinances when installing your service. To prevent the unit from tipping forward and provide a stable installation, the unit must be secured in place with an anti-tip blocking kit. If there is a solid soffit above the unit with clearance between the unit and the soffit of 1" (25) or less, you won't need to block the unit. For installations with clearances of more than 1" (25), you must block the unit with the anti-tip blocking kit (wood block and hardware) provided with each Built-In unit. Refer to the Built-In Installation Instructions packed with the appliance, which provides step-by-step procedures for making sure the unit is installed properly. Dimensions in parentheses are in millimeters unless otherwise specified. 5 Planning Information Built-In Model 632 A D D I N G PA N E L S F R A M E D PA N E L S PANELS 1/4" (6) THICK OR LESS In your plan for panels, be sure you are working with the Sub-Zero panel design family called for in your design. If you have chosen the stainless steel design, the unit will be shipped complete with wrapped stainless steel doors and handle hardware. You will not have to install front door panels. If you and your client have ordered a framed or overlay design model, you will be adding panels to give the unit the custom Sub-Zero look. Specifications on the following pages provide installation considerations for framed and overlay door panels. Side panels can be used with the framed, overlay and stainless steel design applications. Refer to specifications on page 10. Trim reveal 1/4" (6) min 1/4" (6) Panel Framed door panel 1/4" (6) thick or less F R A M E D PA N E L S PANELS THICKER THAN 1/4" (6) Trim reveal 1/4" (6) min Rout to 1/4" (6) thickness If the thickness of the custom panels is less than 1/4" (6), they must be backed up with a sheet of shim material to build the total thickness to 1/4" (6). If the panel is thicker than 1/4" (6), an edge must be routed around the panel to ensure a proper fit. Refer to the illustrations on this page. IMPORTANT NOTE: Routing, recessing or optional extended handles may be required on raised panels for finger clearance under the handle. Refer to the full-scale illustrations on pages 11­14. IMPORTANT NOTE: The weight of each panel cannot exceed 50 lbs (23 kg). The traditional framed models come with an 11" (279) louvered grille and elegant full-length handle. Optional extended full-length handles that provide additional finger clearance for raised panels are available through your Sub-Zero dealer. To obtain local dealer information, visit the Locator section of our website, subzero. com. [. . . ] Contact your Sub-Zero dealer for specifics. To obtain local dealer information, visit the Locator section of our website, subzero. com. Cut-outs for grille and toe kick area Dimensions in parentheses are in millimeters unless otherwise specified. 10 Planning Information Built-In Model 632 H A N D L E P R O F I L E ­ F R A M E D A P P L I C AT I O N OPTIONAL EXTENDED FULL-LENGTH HANDLE 1" (25) 2" (51) 3" (76) STANDARD FULL-LENGTH HANDLE 11/4"(32) PANEL 1"(25) PANEL 3/4"(19) PANEL 1/2"(13) PANEL 1/4"(6) PANEL 1/4"(6) FRAMED PANEL DOOR F U L L - S C A L E T E M P L AT E S HANDLE PROFILE The following full-scale illustrations enable you to understand some of the unique situations you may face as you design the Built-In units into homes. These templates can be easily photocopied or used in your tracings. The full-scale illustration above shows handle placement for the framed application standard full-length handle and the optional extended full-length handle shown in the dashed line. Dimensions in parentheses are in millimeters unless otherwise specified. 11 Planning Information Built-In Model 632 H A N D L E P R O F I L E ­ S T A I N L E S S S T E E L / O V E R L AY A P P L I C A T I O N S STANDARD STAINLESS STEEL HANDLE 1" 2" (51) 3" (76) 11/4" (32) PANEL 1" (25) PANEL 3/4" (19) PANEL 5/8" (16) PANEL 1/2" (13) PANEL 1/4" (6) PANEL 1/4" (6) APPROXIMATE THICKNESS OF WRAPPED STAINLESS STEEL DOOR DOOR NOTE: FOR OVERLAY APPLICATIONS, OPTIONAL STAINLESS STEEL HANDLE MUST BE MOUNTED ON PANEL MINIMUM 5/8" (16) THICK. PA N E L A N D H A N D L E P R O F I L E The full-scale illustration above shows handle placement for the standard stainless steel handle on the wrapped stainless steel door and on overlay panel applications shown in the dashed line. IMPORTANT NOTE: For overlay applications, the optional stainless steel handle must be mounted on a panel at least 5/8" (16) thick. For overlay applications, mount door handles close to the opening edge of the door for ease of opening. Dimensions in parentheses are in millimeters unless otherwise specified. 12 Planning Information Built-In Model 632 PA N E L A N D H A N D L E P R O F I L E ­ 1 3 0 ° D O O R O P E N I N G SUB-ZERO UNIT 130° DOOR OPENING WITH 2" (51) FILLER STRIP (TOP VIEW) SUB-ZERO UNIT FILLER STRIP 2" (51) ALLOW FOR FILLER LAP BEHIND FLANGE MAIN FRAME OVERLAY PANEL 3/4" (19) THICK (NOMINAL) DOOR CLOSED HINGE APPROX PROFILE OF STAINLESS STEEL DOOR AND HANDLE PA N 2) (3 STANDARD FRAMED FULL-LENGTH HANDLE EL PA N 5) EL PA N EL 11 /4" PA NE L DOOR OPEN @ 130° EL 1" (2 /4" (1 9) 3) /2" 1 OPTIONAL FRAMED EXTENDED FULL-LENGTH HANDLE *1 /4" (6 The full-scale illustration above shows the panel and handle profile of a 130° door opening with 2" (51) filler strip for framed applications. [. . . ]