User manual SUB-ZERO 695-PS

[. . . ] Planning Information Built-In Model 695 Side-by-Side Refrigerator / Freezer with Ice and Water Dispenser Front venting allows unit to be completely built in Hermetically sealed refrigeration units Serial and model number plate Lighted electronic control panel Model 695/F Framed Automatic ice maker Adjustable dairy compartment Freezer utility rack Adjustable spillproof glass shelves Adjustable wire shelves Bulk ice dispenser Adjustable door shelves Model 695/F Partial Framed Roll-out freezer baskets Adjustable roll-out utility basket Adjustable door shelves Four-sided magnetic gaskets Egg tray Removable kickplate Model 695/O Overlay High humidity crisper drawer (Stainless steel design shown) Door closers With the installation of a harness kit, these appliances are Star-K compliant to meet strict religious regulations in conjunction with specific instructions found on star-k. org. You may purchase this harness kit through your Sub-Zero dealer. To obtain local dealer information, visit the Locator section of our website, subzero. com. Model 695/S Classic Stainless Steel The Sub-Zero Model 695 side-by-side refrigerator / freezer with ice and water dispenser is available in your choice of the framed, partial framed, overlay or stainless steel design application. [. . . ] Refer to the illustrations on this page. IMPORTANT NOTE: Routing, recessing or optional extended handles may be required on raised panels for finger clearance under the handle. Refer to the full-scale illustrations on pages 13­16. IMPORTANT NOTE: The weight of each panel cannot exceed 50 lbs (23 kg). The traditional framed models come with an 11" (279) louvered grille and elegant full-length handle. Optional extended full-length handles that provide additional finger clearance for raised panels are available through your Sub-Zero dealer. To obtain local dealer information, visit the Locator section of our website, subzero. com. For framed door panel dimensions and dimensions for the optional panel grille for the framed application, refer to specifications on page 7. To install framed panels, refer to the installation instructions shipped with each unit. The thickness of the panel in this area can range from 1/4" (6) to a maximum of 11/8" (29). If the panel is thicker, provisions must be made to rout out a space to accommodate the decorative bezel surrounding the glasswell. If you choose not to use custom wood panels above or below the glasswell for the framed application, a stainless steel insert panel will be provided with the partial framed accessory kit. This accessory kit includes partial framed molding and classic stainless steel inset handle panel to provide a spill-resistant finish above and below the glasswell on the refrigerator door only. Refer to the specifications for this option in the chart below. Grille panel dimensions will be the same as shown for framed panels. With the framed retrofit accessory kit, existing Model 690 door panels can be used on a new Model 695 framed unit. This accessory kit includes framed retrofit moldings and classic stainless steel inset handle panels to accommodate existing Model 690 framed refrigerator and freezer door panels. IMPORTANT NOTE: When using a partial framed or framed retrofit kit, a 1/2" (13) reveal must be maintained on the bezel side of the panel. Both accessory kits are available through your Sub-Zero dealer. To obtain local dealer information, visit the Locator section of our website, subzero. com. H W W Partial Framed Door Panels (identical in size) PA R T I A L F R A M E D PA N E L D I M E N S I O N S Partial framed kit WIDTH HEIGHT Refrigerator Door Panel Freezer Door Panel 17 15/16" (456) 17 15/16" (456) 6711/16" (1719) 6711/16" (1719) Framed retrofit kit Dimensions in parentheses are in millimeters unless otherwise specified. 8 Planning Information Built-In Model 695 O V E R L AY PA N E L S O V E R L AY PA N E L S The overlay design allows decorative panels to cover the door trim for a more seamless appearance that blends with the design of the room. To achieve this look, the most common way is to work with three panels--the decorative overlay panel, a . 10" (3) spacer panel and a 1/4" (6) backer panel. Depending on your cabinet manufacturer, this could be one panel routed for different dimensions or more likely, three different panels. [. . . ] Cut-outs around the toe kick and grille area are required if a 1/4" (6) thick panel will be inserted into the main frame channel. The panel will need to be 24" (610) deep. Refer to the illustration on this page for placement of toe kick and grille area cut-outs. If a 3/8" (10) thick panel is used, the panel will abut the main frame and should be 23 7/8" (606) deep. [. . . ]