User manual SUB-ZERO INDUCTIONUC GUIDE

[. . . ] I NDUCTION C OOKTOP USE & CARE INFORMATION CONTENTS Introducing the Wolf Induction Cooktop Safety Instructions and Precautions Wolf Induction Cooktop Features Wolf Induction Cooktop Use & Care Troubleshooting Guide Service Information Wolf Warranty 3 4 6 8 13 14 15 As you read this Use & Care Information, take particular note of the CAUTION and WARNING symbols when they appear. This information is important for safe and efficient use of the Wolf equipment. signals a situation where minor injury or product damage may occur if you do not follow instructions. states a hazard that may cause serious injury or death if precautions are not followed. In addition, this Use & Care Information may signal an IMPORTANT NOTE which highlights information that is especially important. WOLF ® is a registered trademark of Wolf Appliance Company, LLC I N T R O D U C I N G T H E WO L F I N D U C T I O N C O O K TO P T H A N K YO U Your purchase of a Wolf induction cooktop attests to the importance you place upon the quality and performance of your cooking equipment. We understand this importance and have designed and built your cooktop with quality materials and workmanship to give you years of dependable service. We know you are eager to start cooking, but before you do, please take some time to read this Use & Care Information. [. . . ] To activate Hi-Power mode, touch the OFF ON touch pad for the rear element, then touch HI-POWER. Power from the front element will automatically be diverted to the rear element, and the total output of the front element on HIGH power will be reduced. This reduction in power will be displayed in the control panel. Hi-Power touch pad H HIG T MEL ON OFF OWER HI-P H HIG OFF SIM ON O H HIG OFF T MEL ON OFF OWER HI-P H HIG OFF SIM ON O OFF Lock "key" touch pad Lock mode "key" touch pad Hi-Power mode touch pad 8 W O L F I N D U C T I O N C O O K TO P U S E & C A R E R E S I D UA L H E AT I N D I C AT O R S I N I T I A L S TA RT- U P As an additional safety precaution, residual heat indicator lights will illuminate when the surface temperature of the glass is above 150°F (65°C). Each heating element has an independently controlled light located to the right of the element as shown in the illustration. Even if the cooktop controls are turned off, you are alerted to any area of the cooktop that remains hot. Before operating the cooktop, please read the entire Use & Care Information. Clean the cooktop surface as outlined in the Ceramic Glass Top Cleaning section on page 12. The cooktop surface must be free of any foreign substance, especially those that could melt and permanently adhere to the glass. During the first uses of your new induction cooktop, you may smell a slight burning odor or see light smoke. Both of these conditions are normal in new ceramic glass cooktops. NOTE: A sound may be detected when the cooktop begins operation. IMPORTANT NOTE: When the cooktop is powered up for the first time, the unit will default to Lock mode. To unlock the control panel, refer to the Lock Mode section on page 8. Do not set griddles or oversized pans on residual heat indicator lights. Make sure that the cooktop surface is clean and dry before operating. Do not place hot cooking utensils directly over control panel. Location of indicators H HIG T MEL ON OFF OWER HI-P H HIG OFF SIM ON O OFF Residual heat indicators 9 W O L F I N D U C T I O N C O O K TO P U S E & C A R E C O O K TO P O P E R A T I O N To activate a heating element, touch the OFF ON touch pad that corresponds to the element you wish to use. The power bar indicator graph will begin to blink and show a half-power status. To complete the element activation, touch one of the following symbols or touch pads of the element control while the bar graph is still blinking: Touch the "+" or "­" symbol to set power output to 25% and complete the activation. Touch HIGH to set the power output to full power and complete the activation. Touch MELT to set the power output to the lowest power and complete the activation. To change the power level setting--the element is activated and the power bar graph remains steadily lit: Touch "+" to increase the power level by preset one or two bars on the power bar graph. Touch "­" to decrease the power level by preset one or two bars on the power bar graph. Touch HIGH to increase the power level directly to full power. Touch MELT to decrease the power level directly to the lowest power. IMPORTANT NOTE: If no cookware is placed on a heating element after activating the element, the control will blink for 30 seconds, then the element will automatically shut off. Apply about 1 teaspoon of nonabrasive cleaner such as Elco Cook Top Cleaning Creme, to the surface of the ceramic glass with a lightly dampened clean cloth. Use a second clean cloth to remove any remaining cleaner residue. [. . . ] A power outage may also have caused a disruption in service. The information and images are the copyright property of Wolf Appliance Company, LLC, an affiliate of Sub-Zero Freezer Company, Inc. Neither this book nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Wolf Appliance Company, LLC, an affiliate of Sub-Zero Freezer Company, Inc. © Wolf Appliance Company, LLC all rights reserved. 14 WOLF APPLIANCE PRODUCTS LIMITED WARRANTY RESIDENTIAL USE ONLY FULL TWO YEAR WARRANTY* For two years from the date of original installation, your Wolf Appliance product warranty covers all parts and labor to repair or replace any part of the product that proves to be defective in materials or workmanship. [. . . ]