User manual SUB-ZERO ISLANDHOOD INSTALL GUIDE

[. . . ] P R O I S L A N D V E N T I L AT I O N H O O D S INSTALLATION INSTRUCTIONS C O N TA C T I N F O R M AT I O N Wolf Customer Service: 800-332-9513 Website: wolfappliance. com As you follow these instructions, you will notice WARNING and CAUTION symbols. This blocked information is important for the safe and efficient installation of Wolf equipment. There are two types of potential hazards that may occur during installation. signals a situation where minor injury or product damage may occur if you do not follow instructions. states a hazard that may cause serious injury or death if precautions are not followed. Another footnote we would like to identify is IMPORTANT NOTE: This highlights information that is especially relevant to a problemfree installation. WOLF ® is a registered trademark of Wolf Appliance Company, LLC W O L F P R O I S L A N D V E N T I L AT I O N H O O D S I N S TA L L AT I O N R E Q U I R E M E N T S IMPORTANT NOTE: This installation must be completed by a qualified installer or Wolf authorized service center technician. Installer: Please read the entire Installation Instructions prior to installation. [. . . ] Invert and reattach the transition to the hood with the shipping screws. If you are installing a remote blower, drill a 7/8" (22) hole through the hood framing for the conduit. Refer to the remote blower information on page 14 and follow installation instructions provided with the blower. IMPORTANT NOTE: Do not run wiring for the remote blower through the ductwork. Center Filter Bank Location of Screws for Center Filter Bank Filter Remove filters and center filter bank Dimensions in parentheses are in millimeters unless otherwise specified. 9 W O L F P R O I S L A N D V E N T I L AT I O N H O O D S I N S TA L L T H E I S L A N D H O O D IMPORTANT NOTE: If an optional duct cover is to be used, it must be installed before installing the island hood. Refer to Duct Cover Installation on page 8. ACCESSORIES Optional accessories are available through your Wolf dealer. To obtain local dealer information, visit the Locator section of our website, wolfappliance. com. Mark the center location of the hood. Install 2 x 4 blocking between ceiling joists. If you are installing an internal blower, do not reinstall the center filter bank and filters until the blower installation is complete. Refer to the internal blower information on page 13 and follow installation instructions provided with the blower. 1/4" x 3" (76) Lag Screw #10 x 2" (51) Hex Head Screw Island Hood Top Plate Island hood installation Dimensions in parentheses are in millimeters unless otherwise specified. 11 W O L F P R O I S L A N D V E N T I L AT I O N H O O D S I N S TA L L W I R I N G I M P O R TA N T N OT E You must follow all National Electrical Code regulations. In addition, be aware of local codes and ordinances when installing your service. This ventilation hood must be properly grounded. This unit should be installed by a qualified electrician in accordance with all applicable national and local electrical codes. Run a 120 V AC, 15 amp circuit power cable from the service panel to the electrical box at the center of hood. Supply a minimum of 6' (1. 8 m) of ROMEX cable. Remove the knockout located on the left side of the hood top plate. Refer to the illustration and chart below for the wiring location of your specific model. Insert the conduit through the hole on top of the hood to the electrical box located in center of hood shell. Connect black wire to power supply black wire, white wire to power supply white wire and green wire to green wire or bare wire. Place all wiring connections inside the electrical box and reinstall the cover. Make sure that the wires are secure and that no wires are pinched between the cover and box. Refer to the wiring diagram packaged with the island hood for more information. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. Do not remove the control knob bezel to access hood wiring, this will damage the bezel assembly. Location of Knockout for Wiring Model (A) (B) Transition Cut-Out 8" (203) x 5 7/8" (149) Location of Knockout I363418 I423418 I543418 I663418 1" (25) 2" (51) 8" (203) 14" (356) 1" (25) 1 1/2" (38) 1 1/2" (38) 1 1/2" (38) Letters correspond to the illustration. B A Island hood wiring location 12 I N S TA L L AT I O N I N S T R U C T I O N S INTERNAL B L OW E R IMPORTANT NOTE: Refer to the installation instructions provided with the internal blower for additional mounting and wiring instructions. IMPORTANT NOTE: Use wire connectors or wire nuts approved by UL or C/UL. I B L O W E R - 1 2 0 I N T I N S TA L L AT I O N Remove filters and center filter bank from the island hood. Lift the blower into position inside the hood. [. . . ] Wolf internal, in-line and remote blower assemblies are available as sales accessories through your Wolf dealer. IMPORTANT NOTE: Blower options vary with the cooking surface. Use only a Wolf blower with the Pro island ventilation hood. INTERNAL BLOWER IBLOWER-120INT (804703) ­ 1200 CFM internal blower for all island hoods. [. . . ]