User manual SUPERMICRO H8QME-2

[. . . ] This product, including software and documentation, is the property of Supermicro and/or its licensors, and is supplied only under a license. Any use or reproduction of this product is not allowed, except as expressly permitted by the terms of said license. IN NO EVENT WILL SUPER MICRO COMPUTER, INC. BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. [. . . ] JI2C2 LED3 LEDM1 JIPMB1 BMC CTRL LAN CTRL BMC FAN8 JPG1 JPB1 FAN7 LAN2 LAN1 IPMI_LAN SP1 LAN CTRL JD1 JPL1 JI2C1 JI2C2 A JTPM1 JVRM_I2C1 JVRM_I2C2 B CLK CTRL CPU1 SLOT3 PCI-E 3. 0 X8 CPU1 SLOT5 PCI-E 3. 0 X8 PCH CPU1 SLOT4 PCI-E 3. 0 X8 CPU2 SLOT6 PCI-E 3. 0 X16 CPU2 SLOT7 PCI-E 3. 0 X8 JBT1 X9DRD-iF Rev. 1. 10 G1 H1 F1 JPW4 E1 CPU2 JPME2 JPME1 JWD1 JSD1 BIOS JRK1 I-SATA0 I-SATA2 I-SATA4 SCU0 SCU2 USB4/5 USB8/9 T-SGPIO1JSTBY1 JL1 FAN6 I-SATA1 C1 D1 B1 A1 I-SATA3 I-SATA5 SCU1 SCU3 T-SGPIO2 S-SGPIO1 CPU1 JVR2 JPW3 JBAT1 JOH1 + JPW1 JPW2 :OH LED LED2 JPW5 FAN4 JVR1 FP CTRL JPI2C1 FAN1 FAN5 FAN2 FAN3 JF1 2-39 X9DRD-iF/LF Motherboard User’s Manual 2-9 Onboard LED Indicators GLAN LEDs There are two GLAN ports on the motherboard. Each Gigabit Ethernet LAN port has two LEDs. The Yellow LED on the right indicates activity. The Link LED on the left side may be green, amber or off to indicate the speed of the connection. See the table on the right for more information. Link LED Activity LED Rear View (when facing the rear side of the chassis) GLAN Activity Indicator (Right) LED Settings Color Yellow Status Flashing Definition Active GLAN Speed/Link Indicator (Left) LED Settings LED Color Off Green Amber Definition No Connection or 10 Mbps 100 Mbps 1 Gbps LAN 1/LAN 2 IPMI Dedicated LAN LEDs In addition to LAN 1/LAN 2, an IPMI Dedicated LAN is also located on the I/O Backplane of the motherboard. The amber LED on the right indicates activity, while the green LED on the left indicates the speed of the connection. See the table on the right for more information. Link LED IPMI LAN Activity LED IPMI LAN Link LED (Left) & Activity LED (Right) Definition 100 Mbps Active Link (Left) Activity (Right) Green: Solid Amber: Blinking IPMI LAN (X8ST3-F) Color/State COM2 JUIDB USB2/3 VGA USB0/1 COM1 USB6 A. IPMI LAN LEDs JTPM1 JPW4 LED3 LEDM1 JIPMB1 BMC CTRL LAN CTRL BMC FAN8 JPG1 JPB1 FAN7 LAN2 LAN1 IPMI_LAN SP1 LAN CTRL JD1 JI2C1 JI2C2 CLK CTRL JPL1 JVRM_I2C1 JVRM_I2C2 CPU1 SLOT3 PCI-E 3. 0 X8 CPU1 SLOT5 PCI-E 3. 0 X8 PCH CPU1 SLOT4 PCI-E 3. 0 X8 CPU2 SLOT6 PCI-E 3. 0 X16 CPU2 SLOT7 PCI-E 3. 0 X8 JBT1 X9DRD-iF Rev. 1. 10 G1 H1 F1 E1 CPU2 JPME2 JPME1 JWD1 JSD1 BIOS JRK1 I-SATA0 I-SATA2 I-SATA4 SCU0 SCU2 USB4/5 USB8/9 T-SGPIO1JSTBY1 JL1 FAN6 C1 D1 B1 A1 B JVR2 I-SATA1 I-SATA3 I-SATA5 SCU1 SCU3 T-SGPIO2 S-SGPIO1 FAN4 CPU1 JBAT1 JOH1 + A JPW3 JPW1 JPW2 :OH LED LED2 JPW5 FP CTRL JPI2C1 FAN1 FAN5 FAN2 FAN3 JF1 JVR1 2-40 Chapter 2: Installation Onboard Power LED An Onboard Power LED is located at LED2 on the motherboard. Be sure to turn off the system and unplug the power cord before removing or installing components. Refer to Appendix A for details on beep codes. System Boot Failure If the system does not display POST or does not respond after the power is turned on, check the following: 1. Check for any error beep from the motherboard speaker. • there is no error beep, try to turn on the system without DIMM modules inIf stalled. If there is still no error beep, try to turn on the system again with only one processor installed in CPU Socket#1. If there is still no error beep, replace the motherboard. • there are error beeps, clear the CMOS settings by unplugging the power If cord and contracting both pads on the CMOS Clear Jumper (JBT1). (Refer to Section 2-8 in Chapter 2. ) 2. Remove all components from the motherboard, especially the DIMM modules. Make sure that system power is on, and memory error beeps are activated. 3. Turn on the system with only one DIMM module installed. If the system boots, check for bad DIMM modules or slots by following the Memory Errors Troubleshooting procedure in this Chapter. Losing the System’s Setup Configuration 1. Make sure that you are using a high quality power supply. A poor quality power supply may cause the system to lose the CMOS setup information. Refer to Section 2-7 for details on recommended power supplies. 2. The battery on your motherboard may be old. Check to verify that it still supplies ~3VDC. [. . . ] Con-Out includes Video Controller, PCI or Serial Console Redirection, IPMI SOL. 1 beep per device Refresh 1 beep or each USB device detected X9 IPMI Error Codes 1 Continuous Beep System OH System Overheat A-1 X9DRD-iF/LF Motherboard User’s Manual Notes A-2 Appendix B: Software Installation Instructions Appendix B Software Installation Instructions B-1 Installing Software Programs The Supermicro ftp site contains drivers and utilities for your system at ftp://ftp. Some of these must be installed, such as the chipset driver. After accessing the ftp site, go into the CDR_Images directory and locate the ISO file for your motherboard. [. . . ]