User manual SUPERMICRO X7SBL-LN2

[. . . ] Copyright © 2009 SUPERMICRO TECHNOLOGIES CO. , LTD. All rights reserved. http://www. tp-link. com FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] DMZ host forwards all the ports at the same time. Any PC whose port is being forwarded must have its DHCP client function disabled and should have a new static IP Address assigned to it because its IP Address may change when using the DHCP function. You can set up DMZ host on this page shown in Figure 4-33 39 Figure 4-33 DMZ To assign a computer or server to be a DMZ server: 1. Click the Enable radio button Enter the IP address of a local PC that is set to be DMZ host in the DMZ Host IP Address field Click the Save button. Note: After you set the DMZ host, the firewall related to the host will not work. 4. 9. 4 UPnP The Universal Plug and Play (UPnP) feature allows the devices, such as Internet computers, to access the local host resources or devices as needed. UPnP devices can be automatically discovered by the UPnP service application on the LAN. You can configure UPnP on this page that shown in Figure 4-34: Figure 4-34 UPnP Settings Current UPnP Status - UPnP can be enabled or disabled by clicking the Enable or Disable button. As enabling UPnP may present a risk to security, this feature is disabled by default. Current UPnP Settings List - This table displays the current UPnP information. · · · · · · App Description ­ The description provided by the application in the UPnP request External Port - External port, which the router opened for the application. Protocol - Shows which type of protocol is opened. Internal Port - Internal port, which the router opened for local host. LAN Port - Enter a LAN Port or a range of LAN ports in the field. Keep the field blank, which means all LAN ports have been put into the field. 42 4. WAN IP Address - Enter a WAN IP Address or a range of WAN IP Addresses in the field, in dotted-decimal notation format. For example, 61. 145. 238. 6 - 61. 145. 238. 47. Keep the field blank, which means all WAN IP Addresses have been put into the field. WAN Port -Enter a WAN Port or a range of WAN Ports in the field. Keep the field blank, which means all WAN Ports have been put into the field. Protocol - Select which protocol is to be used, either TCP, UDP, or All (all protocols supported by the router). Action - Select either Allow or Deny through the router. Status - Select Enabled or Disabled for this entry from the Status pull-down list. Click the Save button to save this entry. [. . . ] Select Use the following DNS server addresses. In the Preferred DNS Server field you can enter the same value as the Default gateway or type the local DNS server IP address. 92 Figure 0-4 Now: Click OK to keep your settings. 93 Appendix C: Specifications General Standards and Protocols Safety & Emission Ports IEEE 802. 3, 802. 3u, 802. 11b and 802. 11g, TCP/IP, DHCP FCCCE One 10/100M Auto-Negotiation LAN RJ45 port, supporting passive PoE 10BASE-T: UTP category 3, 4, 5 cable (maximum 100m) EIA/TIA-568 100 STP (maximum 100m) Cabling Type 100BASE-TX: UTP category 5, 5e cable (maximum 100m) EIA/TIA-568 100 STP (maximum 100m) Wireless Wireless Data Rates Wireless Encryptions 54/48/36/24/18/12/9/6Mbps or 11/5. 5/3/2/1Mbps 64/128/152-bit WEP, WPA/WPA2, WPA-PSK/WPA2-PSK Physical and Environment Working Temperature Working Humidity Storage Temperature Storage Humidity -10~40 10% ~ 90% RH, Non-condensing -40~70(-40~158) 5% ~ 90% RH, Non-condensing 94 Appendix D: Glossary 2x to 3x eXtended RangeTM WLAN Transmission Technology - The WLAN device with 2x to 3x eXtended RangeTM WLAN transmission technology make its sensitivity up to 105 dB, which gives users the ability to have robust, longer-range wireless connections. With this range-enhancing technology, a 2x to 3x eXtended RangeTM based client and access point can maintain a connection at as much as three times the transmission distance of traditional 802. 11b and 802. 11g products, for a coverage area that is up to nine times greater. A traditional 802. 11b and 802. 11g product transmission distance is about 300m, a 2x to 3x eXtended RangeTM based client and access point can maintain a connection transmission distance may be up to 830m. [. . . ]