User manual SURGEX XR315 1.0

[. . . ] USER MANUAL SurgeX XR315 SurgeX® Surge Eliminator For Residential Applications Software Version 1. 0/1. 1 1 DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3. 1 120 VOLT CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] This can be useful, for example, to power-up equipment faster than normal if there is an emergency and a PA is required. If the special delay is required select "Special Delay", or if not, select "Use Main Delays". This is the special delay (in seconds) for use only during an over-ride. The previous menu item must have been set to enable this delay. Over-Ride Option Over-Ride Delay 5. 3 12V dc Output The programmable 12V dc output provides a nominal 12 volts at up to 40mA of direct current and is available at the rear of the unit. The 12V dc output can be used to provide confirmation to a central controller, to control another power distribution product, to drive LEDs, or to provide feedback to the previous XR315 in a cascaded chain. Please see the applications section for full details on setting up an expanded system. There are three menu items to control the 12V dc output: one to select the mode of operation and two to set the delay times. The two delay times are only applicable when option A, B, or C is selected for 12V dc Output. There is additional information on the 12V dc output in sections 3. 2. 3 and 3. 2. 4. If the DC output is not used it can be left at any setting. 12V dc Output Select "Confirm" if you are using the DC output for confirmation or to drive a relay. Options "A", "B or "C" synchronize the operation of the relay to the same internal trigger as the receptacles on the rear panel of the XR315. Choose A, B, or C when the output is used to control an "RT" type SurgeX. Select "LED" if you are driving LEDs. (This causes the unit to flash the LEDs during power-up and powerdown. ) Select "Cascade" only when setting up two or more XR315s in cascade. All these options are covered in detail in the applications section. Set the delay time in seconds for the 12V dc output activation. This delay time begins with the same internal trigger as the receptacles on the rear panel of the XR315. Set the delay time in seconds for the 12V dc output deactivation. This delay time begins with the same internal trigger as the receptacles on the rear panel of the XR315. 12V Delay On 12V Delay Off 10 5. 4 Auxiliary Relay The programmable auxiliary relay provides a single normally-open contact which is available at the rear of the unit. The aux relay can be used to provide confirmation to a central controller, to control another power distribution product, or for controlling another XR315 when two or more are ganged or cascaded together. Please see the applications section for full details on setting up an expanded system. [. . . ] If you are certain that power is being supplied to the unit, consult the factory for assistance. Unit will not power up from remote control connection If you have performed initial checks as above and the unit will still not power up it could be because the "down" input (terminal 2) is being held active all the time. Remove the terminal block from the rear and check that the Up and Down signals are correct with a meter. The front panel button will not work Check whether the front panel button has been programmed to Delay or Disable. [. . . ]