User manual SWISHER FC-17 DUMP CART

[. . . ] This warranty is subject to the following limitations and exclusions: 1) Commercial Use This product is not intended for commercial use and carries no commercial warranty. This warranty applies only to products which have been properly assembled, adjusted, and operated in accordance with the instructions contained within this manual. This warranty does not apply to any product of Swisher Mower Co. , Inc. , that has been subject to alteration, misuse, abuse, improper assembly or installation, shipping damage, or to normal wear of the product. Excluded from this warranty are normal wear, normal adjustments, and normal maintenance. 2) Limitation 3) Exclusions In the event you have a claim under this warranty, you must return the product to an authorized service dealer. [. . . ] NB719 10619 12205 12186 NB600 NB718 NB135 NB159 NB274 NB275 12206 NB247 NB603 NB179 12207 Qty. 10 2 49 22 51 32 51 32 51 32 1 1 2 4 2 Part Description M8 x 20 Hex Bolt M6 x 20 Hex Bolt M6 X 16 Round Head Bolt M8 X 16 Round Head Bolt M6 Nut M8 Nut Ø 6 Lock Washer Ø 8 Lock Washer Ø 6 Flat Washer Ø 8 Flat Washer Lock Pin Hair Pin Cotter Pin Large Washer Wheel Hub Cap Note: You may have extra nuts & Bolts when finished Assembly Instructions: Step 1: Main Panels Assembly Attach the main panels bottom body and side body by M8 Bolts, 8 Lock Washer and M8 Nut, tighten the bolts. Step 1 Hardware Needed: 18-M8x20 Round Head Bolt 18-8 Lock Washer 18-M8 Nut Figure #1 Step 2: Attach Main Cart Panels Set cart upright as shown in figure #1 on a level surface. Connect the center of the panels using M6x16 bolts, 6 lock washer, and M6 nut. Step 2 Hardware Needed: 9 ­ M6x16 Bolt 9 ­6 Lock Washer 9 ­ M6 Nut Figure #2 Step 3: Attach Tailgate Brace and Tailgate Holding Guides First attach the bottom piece of the tailgate brace using M8x20 round slotted bolts, 8 lock washer, and M8 Nut. Next, attach the side pieces of the tailgate brace to the outside, and attach the tailgate holder guide to the inside of panel. Use M6x20 bolts, 6 lock washer, and M6 nut. Same bolt for both pieces SEE Figure #2. Step 3 Hardware Needed: 6 ­ M8x20 Round Head Bolt 6 ­8 Lock Washer 6 ­ M8 Nut 6 ­ M6x20 Bolt 6 ­6 Lock Washer 6 ­ M6 Nut Figure #3 Step 3A: Now tighten bottom bolts, and side bolts. Wait to tighten bolts connecting the bottom of main body panels until the next step. Step 4: Attach Front Panel With care, completely turn over the main body to rest the end which was just assembled. Next, attach the front panel using M6x16 bolts, 6 lock washers, and M6 nuts. Tighten bottom bolts, side bolts, and the center connection bolts from Step 1. Step 4 Hardware Needed: 10 ­6 Lock Washer 10 ­ M6 Nut 10 ­ M6x16 Bolt Figure #4 Step 5: Attach Wheel Support Attach the wheel support as shown in figure #4 below using M8x20 round head bolts, 8 lock washer, and M8 nut. Step 5 Hardware Needed: 8 ­ M8x20 Round Head Bolt 8 ­8 Lock Washer 8 ­ M8 Nut Figure #5 Step 6: Attach Stand Bracket Support Attach the stand bracket as shown in figure #5 using M6x16 bolts, 6 lock washer, and M6 nut. Step 6 Hardware Needed: 4 ­ M6x16 Bolt 4 ­6 Lock Washer 4 ­ M6 Nut Figure #6 Step 7: Attach Front Corner Cap/Brace Attach front corner braces and bolt back bracket as shown in figure #6 using M6x16 bolts, 6 lock washer, and M6 nut. Step 7 Hardware Needed: 6 ­ M6x16 Bolt 6 ­6 Lock Washer 6 ­ M6 Nut Figure #7 Step 8: Attach Latch Lock to Tongue Attach latch lock to tongue using M6x16 bolts, 6 lock washer, and M6 nut. See figure #7 for direction of latch lock. Note: do not connect latch lock pieces to each other, only to the tongue. Step 8 Hardware Needed: 2 ­ M6x16 Bolt 6 ­6 Lock Washer 6 ­ M6 Nut Note: Latch Lock includes: 1 ­ Spring 2 ­ Side pieces 1 ­ Angle Lock Figure #8 Step 9: Attach Hitch Pin Bracket to Tongue Attach hitch pin bracket to tongue using 8x20 bolts, 8 lock washer, and M8 nut. Step 9 Hardware Needed: 2 ­ M8x20Bolt 2 ­8 Lock Washer 2 ­ M8 Nut Figure #9 Step 9A: Attach Axle and Trailer Tongue See Figure 9A. [. . . ] Insert bolts into the lower back corners of tailgate brace with tailgate in place. Hardware needed: 4 ­ M6x20 Bolt 4 ­ M6 Lock Washer 4 ­ M6 Nut The Cart is fully assembled. Be sure all connections are tight. OPERATION NOTES: A full capacity load is 1500 pounds, DO NOT exceed rated capacity. Cart only to be used with lawn tractor or ATV. [. . . ]