User manual SWISHER LS5-24S

[. . . ] As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. If you violate any of these rules, you may cause serious injury to yourself or others. Learn to operate this equipment in a safe manner. Do not under any circumstances alter this log splitter. [. . . ] Never operate your splitter on wet, muddy, or icy surfaces. Safe footing is essential in preventing accidents. · · · · · · · · · · · · · · · · Never make adjustments or repairs with the engine running. Never attempt to split woods across the grain. Some types of wood may burst or fly out of your splitter and result in injury. Both ends of the log should be cut as squarely as possible to prevent the log from riding out of the splitter during operation. Log length should be kept to 24" or less. MOVING SAFETY · Do not allow persons to ride on splitter. Do not carry any cargo or wood on your splitter. ·Be sure the Kick Stand is up and out of the way before transporting. Retract kickstand by removing pin , rotating up, and replacing the pin ·Never exceed 5 MPH with your splitter. Be cautious when traveling over rough terrain. ·Be aware of the extra width of the splitter while turning, parking , and all driving situations. · Safety Decals Replace decals immediately if damaged OD08 Operator Instruction Decal OD21 Danger Decal OPERATION Intended use: This log splitter is intended and designed to only split wood. Doing so can cause injury or VOID THE WARRANTY. ASSEMBLY INSTRUCTIONS This log splitter has been assembled at the factory. Refer to the drawings and part lists should it become necessary to disassemble the unit for repair or replacement of parts. IMPORTANT: This unit is shipped without hydraulic oil, after cycling the splitter wedge several times to purge the air, check the oil reservoir and bring to a safe level. WARNING: Exercise extreme caution, as parts are very heavy. Sufficient persons or mechanical handling equipment should be used. ·General Assembly: Remove top, sides and ends of crate. Cut all retaining straps and remove the lag bolt that secures the kickstand to the pallet. Attach splitter to skid steer and lift off of the pallet. ·Check both the horizontal and vertical positions for any "kinks" in the hoses. Note: Always make sure beam is locked securely into place. [. . . ] The wedge is heavy and may still have sharp edges, wear gloves while handling the wedge. REPAIR PARTS Your Swisher Log Splitter has been produced with components designed specifically to this machine. Although standard springs, hardware, etc. may look familiar to parts used on other machinery, they may in some cases be made of a different construction and/or materials. SEE DETAIL SHEET Assembly Detail LS 5-24 Skid Steer Splitter SERVICE PARTS Please have Model and Serial Numbers ready when ordering parts. ITEM NUMBER 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 DESCRIPTION Mounting Plate Beam Weldment Kick Stand Stand Plate Assembly 3/8 - 16 X 3 Grade 5 Bolt 3/8-16 Nylock Nut Saftey Hitch Pin 3/8 - 16 X 1 1/4 Grade 5 Bolt 3/8-16 Nylock Nut Grease Fitting 5/16-18 X 4 1/2 Grade 5 Bolt 5/16-18Lock Nut 1/8 X 1 1/4 Roll Pin 1/2 "lat Washer Spring - Compression Lock Pin Hydraulic Pressure Hose Flat Face Coupling Male Flat Face Coupling Female Hose Sleeve ( Not Shown) Sleeve Clamps ( Not Shown ) 3/8 Washer PART NUMBER 7599TK 7600C 7386TK 7603TK NB164 NB182 H-10 NB618 NB182 NB704 NB513 NB558 NB187 NB555 7429 7595TK 7613 7609 7610 7611 NB656 NB271 59 60 63 64 65 66 78 79 80 81 76 82 74 68 61 67 73 69 70 75 77 71 72 62 61 BEAM DETAIL ITEM NUMBER 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 DESCRIPTION CLIP PIN STEEL PIN HYDRAULIC FITTING STATIONARY LINE ASSEMBLY RAM CYLINDER 1/2-13 X 3 GR5 BOLT SPLITTING WEDGE 1/2-13 X 2 1/2 GR5 CARRIAGE BOLT RETURN LINE FITTING 1/2-13 JAM 2-WAY LOCK NUT 2-WAY PIPE NIPPLE MASTER CHAIN LINK COTTER PIN VALVE INLET FITTING VALVE CONTROL W/ LEVER BEAM WELDMENT 1/4 X 1 CLEVIS PIN 1/2-13 NUT VALVE LEVER & GRIP THIN GIB PLATE THICK GIB PLATE BOTTOM GIB PLATE PART NUMBER NB642 7293 7291 7288TK 7355TK NB131 7233TK NB643 7617 NB121 7292 7424 NB597 7617 7287TK 7600C NB522 NB213Z 7423/7425 7388TK 7237TK 7333TK LOG SPLITTER OWNER'S MANUAL HOW TO ORDER REPAIR PARTS: Each Log Splitter has its own serial number. [. . . ]