User manual SYMPHONIC SC3813

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The caution marking is located on the rear of the cabinet. IMPORTANT SAFEGUARDS 1. Read instructions-All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions-The safety and operating instructions should be retained for future reference. 3. Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow Instructions-All operating and use instructions should be followed. [. . . ] · TV/VCR power must be turned on. Press the PLAY/K or STOP/L button to point to "REPEAT PLAY". Press the F. FWD/B or REW/s button repeatedly until your desired selection [ALL] or [BLANK] appears. RENTAL B REPEAT PLAY AUTO RETURN [OFF] [ALL] [OFF] 1 Insert a prerecorded tape 3 Exit the Repeat Play setting If the erase-protection tab has been removed, the TV/VCR will start playback automatically. Press the MENU button on the remote control to return to the TV mode. 2 To begin playback PLAY B 4 Start playback Press the PLAY button. Note: If any menu is activated on the screen, the PLAY button does not function. Press the MENU button to clear the menu. then, press the PLAY button. Press the PLAY button to start the Repeat Play. · Once you select the Repeat Play mode, it stays in effect even after you turn off the TV/VCR. · If the Rental mode is set [ON], the "RENTAL PLAY B" display has priority. STOP 3 To stop playback Press the STOP button when playback is completed. TO CANCEL THE REPEAT PLAY MODE Repeat steps [1] and [2], select [OFF] using the F. FWD/B or REW/s button on the remote control. Press the MENU button on the remote control to return to TV mode. If there is a power failure of any kind, the unit will retain its memory for this feature. - 16 - EN 9J27 SEARCH PICTURE SEARCH This feature is very useful in finding or skipping over a particular scene on a tape. 1)You may view a video tape at a high speed in either a forward or reverse direction by pressing the F. FWD or REW button during playback. (in the SP / LP / SLP modes) 2)Press it again and the TV/VCR will now search in super high speed. Press the PAUSE/STILL button so that the noise lines change position on the screen so you can see the picture in its entirety without distracting noise lines. NOTE: This feature can be activated ONLY when viewing a tape recorded in the SLP mode. If the tape was originally recorded in the SP or LP mode, the still picture may revert to black and white in addition to the "noise bars". This is normal. RENTAL PLAYBACK This function enables you to improve the picture quality when playing back worn cassettes such as rented tapes. 1 Select "USER'S SET UP" ­MENU­ TIMER PROGRAMMING PICTURE CONTROL SETTING CLOCK CHANNEL SET UP B USER'S SET UP LANGUAGE [ENGLISH] ZERO RETURN TIME SEARCH Press the MENU button on the remote control. Press the PLAY/K or STOP/L button to point to "USER'S SET UP". Then, press the F. FWD/B button. VERTICAL HOLD CONTROL In the Pause/Still mode only, when the picture begins to vibrate vertically, stabilize the picture by pressing the CHANNEL K or L button. NOTE: If there are video noise lines on the screen, reposition or reduce them. Refer to "NOISE CANCEL". 2 Set "RENTAL" to [ON] ­ USER'S SET UP ­ Press the PLAY/K or STOP/L button to point to "RENTAL". Press the F. FWD/B or REW/s button until [ON] appears. B RENTAL REPEAT PLAY AUTO RETURN [ON] [OFF] [OFF] 3 Exit the Rental setting TRACKING ADJUSTMENT · Tracking adjustment will be set automatically · (Digital Tracking function) when you start playback. However when playing pre-recorded tapes or tapes recorded on units other than your own, noise lines (black and white streaks) may appear on the playback picture. If this occurs, you can adjust the tracking control manually by pressing the CHANNEL K or L button until the streaks disappear. [. . . ] 4) Pulse el botón PLAY/K o STOP/L hasta que aparezca el día del mes deseado. (Ejemplo: 6 - 06) Luego, pulse el botón F. FWD/B. 5) Pulse el botón PLAY/K o STOP/L hasta que aparezca el año deseado. (Ejemplo: 2003) Luego, pulse el botón F. FWD/B. [. . . ]